PDF《DONG GUAN RUI FENG TECHNOLOGY&》

东莞市凡睿电子科技有限公司 DONG GUAN RUI FENG TECHNOLOGY&

ELECTRONICS CO.

oLTD. TEL:(0769)81805438/86866001

13751429385 FAX(0769)82991458 E-mail: [email protected]

网址:http://dgruifengkj.cn.alibaba.com 地址:东莞市茶山镇京山第三工业区 RS17 系列旋转式多路开关规格书 东莞市凡睿电子科技有限公司 DONG GUAN RUI FENG TECHNOLOGY&

ELECTRONICS CO.oLTD. TEL:(0769)81805438/86866001

13751429385 FAX(0769)82991458 E-mail: [email protected]

网址:http://dgruifengkj.cn.alibaba.com 地址:东莞市茶山镇京山第三工业区

1、一般事项 General 1-1 适用规格 Scope 本规格书适用于

17 型多路开关. This specification applies to more than

17 type way switch 1-2 标准状态 Standard atmospheric conditions 除另有规定外,测量应在以下状态下进行: Unless otherwise specified , the standard range of atmospheric conditions For making measurements and test is as following limits: 温度Ambient temperature : 15℃ to 35℃ 相对湿度 Relative humidity :

25 % to 85% 气压Air pressure :

86 kPa to

106 kPa 1-3 使用温度围 Operating temperature range :-

20 ℃ to +70 ℃ 1-4 保存温度围 Storage temperature range :-

30 ℃ to +85 ℃

2、构造 Construction 2-1 尺寸 Dimensions 见所附成品图 Refer to attached drawing 1.Mechanical Characteristics 1.机械特性 Item 项目 Measuring condition 测试条件 Specifications 规格 2.1 Changeover 切换角度 Effective switching angles 有效切换角度 30° ±3° Rotation operation (Encoder block) 回转操作 2.2 Encoderrotationtorque 回转力矩 100~500gf.cm 2.3 Push-pullstrength 轴的推拉强度 Push and pull static load of 8Kg shall be applied to the shaft in the axial direction for 10s.(after soldering of the PC board)在轴端,沿轴向施加 10kg 的静负荷力推和拉各

10 秒钟(产品焊锡固定在 PCB 上.) 10kg min 2.4 Shaftstop-perstrength 轴转动止档强度 Rotatioual morment shall be applied to the shart for is at both end. 将轴旋转至两边止档位置 6kg min 2.5 轴摆动 Shaft wobble 在轴前端 5mm 处,沿径向瞬 间施加 50mN(0.51Kgf ・cm) 的力.A momentary load of 50mN?m shall be applied at the point 5mm from the tip of the shaft in a direction perpendicular to the axis of shaft. 0.8xL/30mm p-p 以下(L 是 安装长度,按比例计算) 0.8xL/30mm p-p MAX (L:shaft length) 2.6 轴的回转方向摆动 Shaft playin rota-tional wobble 使用角度板测定. Measurement with jig for rotational angle. 4°以内(5°Max) 东莞市凡睿电子科技有限公司 DONG GUAN RUI FENG TECHNOLOGY&

ELECTRONICS CO.oLTD. TEL:(0769)81805438/86866001

13751429385 FAX(0769)82991458 E-mail: [email protected]

网址:http://dgruifengkj.cn.alibaba.com 地址:东莞市茶山镇京山第三工业区 2.Encoder electrical characteristic s 2.电气特性 Item 项目 Measuring condition 测试条件 Specifications 规格 3.1 Sections 段数

2 3 ?4

5 6

7 8 3.2 Poles 极数

1 ?2 3.3 Rating 额定值 Rating of voltage and current between COM and A (COM and B). C 端和 A 端(C 端和 B 端)间额定电压和电流 D.C16V 0.3A 3.4 Insulation resistance 绝缘电阻 Measure to Apply D.C250V. (Between terminal for reinforcing and the other terminals) D.C250V 测试(在塑胶与接线端之间) 50MΩ min. 3.5 Withstand voltage 耐电压 Apply A.C100V for 1min. (Between terminal for reinforcing and the other terminals) A. C100V1 分钟(在塑胶与接线端之间) No damage. Arc and dielectric breakdown. 无损伤、电弧和电故障 4.Endurance 4.耐久特性 Item 项目 Measuring condition 测试条件 Specifications 规格 4.1 Heat resistance 耐热特性 TemperatureEEE85±2℃ TimeEEEEEE96 ±10hours After that ,leave in ordinary temp and humidity for 1.5 hour. Then measure. 温度EEEE85±2℃ 时间EEEE96 ±10 小时 然后放置在常温和湿度下 1.5 小时再测试. Specification in clause all items in shall be satisfied. 所有项应满足初期规格 4.2 Moisture resistance 耐湿特性 TemperatureEEEE 40±2℃ Humidity EEEE 90~95%Rh Time EEEE 96±

10 hours After that ,leave in ordinary temp and humidity for 1.5 hour. Then measure. 温度EEEE 40±2℃ 湿度EEEE 90~95%Rh 时间EEEE 96±

10 小时 然后放置在常温和湿度下 1.5 小时再测试. The same as above. 同上 4.3 Low temperature resistance 耐寒特性 Temperature EEE -20±2℃ Time EEEE 96±

10 hours After that ,leave in ordinary temp and humidity for 1.5 hour. Then measure. 温度 EEE -20±2℃ 时间EEEE 96±

10 小时 然后放置在常温和湿度下 1.5 小时再测试. The same as above. 同上 东莞市凡睿电子科技有限公司 DONG GUAN RUI FENG TECHNOLOGY&

ELECTRONICS CO.oLTD. TEL:(0769)81805438/86866001

13751429385 FAX(0769)82991458 E-mail: [email protected]

网址:http://dgruifengkj.cn.alibaba.com 地址:东莞市茶山镇京山第三工业区 4-4 耐落下性 Free falling 制品从 60cm 高度以任意方向自由落到m展在 水泥地面上的塑胶垫上. The encoder shall be fallen freely at any posture from 60cm height to the concrete floor covered with vinyl-tile. After which measurement shall be made. 没有明显的变形、破损.应 满足初期规格.(但端子变 形除外) No excessive deformation or damage. (Except the defor-mation of terminals.)And specifications in clause4.1~4.6 and 5.1~5.3 shall be satisfied. Item 项目 Measuring condition 测试条件 Specifications 规格 4-5 轴套锁紧强度 Bushing nut Tightening strength 依下图(图五)安装方式. Tighten the nut according to <

fig.5 >

图五 <

fig.5 >

6.2 in-lbs (7.1Kgf ・cm) 以下之力使用. Tightening torqu to be no greater than 6.2 in-lbs

5、耐久性能 Endurance characteristics 5-1 回转寿命 Rotational life 在无负荷条件下轴以 800/h 速度回转 20,000 周. The shaft of encoder shall be rotated to 20,000 cycles at a speed of 800/h without electrical load, after which measurements shall be made. Contact resistance100 mΩ or less Specification in clause shall be satisfied. 接触电阻: ≤ 100mΩ. 其它应满足初期规格

6、焊接条件 Soldering conditions 6-1 手工焊接 Manual soldering 温度 260℃以下,时间

5 秒以内. Bit temperature of soldering iron :260℃ or less. Application time of soldering iron :within 5s. 6-2 槽焊 Dip soldering 使用基板:t=1.6 的单面覆铜板. Printed wiring board: Single-sided copper clad laminate board with thickness of 1.6mm. 焊剂:采用比重为 0.83±0.05 以上的焊料和发泡式助焊剂,浸入深度不超过基板厚度的 二分之一,且基板表面不得有焊剂流入. Flux: Specific gravity: 0.83 or more. Flux shall be applied to the board using a bu........