PDF《产品规格书》

1 minute, according to the below method. (1) Between terminals. (2) Between terminal and Body. 输入 250V AC 电压

1 分钟, 按如下接触方法测 试: (1) 端子与端子之间. (2) 端子与外壳之间. WITHOUT DAMAGE TO PARTS ARCING OR BREAKDOWN ETC. 没有绝缘破坏等异常 6.4 Bouncing 触点抖动 Lightly striking the center of the stem at a rate encountered in normal use (3 to

4 operations per sec), Bounce shall be tested when ON and OFF . 在正常使用中(以每秒 3-4 次周期)轻轻地在手 柄中心加?,在通与断瞬间测试抖动 Before Life cycle: On: 5ms MAX,5 毫秒以下 Off: 5ms MAX,5 毫秒以下 After Life cycle: On: 10ms MAX,10 毫秒以下 Off: 10ms MAX,10 毫秒以下 Product Specification P/N: CSL903610D01 DOC. No.: KH-PS1704-53 Rev.: A Page: 5/9 Confidential All Right Reserved COPYRIGHT Kaihua Electronics Co.,LTD 7. Mechanical Performance/机械性能: Item 项目 Description 项目描述 Test Condition 测试条件 Requirement 规格要求 7.1 Operation force 操作力 Place the switch such that the direction of switch operation is vertical and then gradually increase the load applied to the center and around of the stem, the maximum load required for the stem to come to a stop shall be measured.开关的动 作方向为垂直放置开关向推柄中心及左右逐 渐地增加负荷直到推柄停止时所测?的最大 负荷 200gf±50gf 7.2 TRAVEL TOCLOSURE 动作?程 IN THE HORIZONTAL DIRECTION SWITCH HANDLE OPRATION,WITH AN EQUAL TO 2TIMES THE THRUST OF THE SWITSH FORM ONE POSITION TO THE NEXT GEAR, MOVING DISTANCE MEASURING HANDLE. 在开关推柄运?的水平方向,以一个等于2 倍推?使开关从 一个档位运动到下一档位,测?推柄的移动 距离. 2mm±0.2mm Product Specification P/N: CSL903610D01 DOC. No.: KH-PS1704-53 Rev.: A Page: 6/9 Confidential All Right Reserved COPYRIGHT Kaihua Electronics Co.,LTD 7.3 Static Strength 静止强度 AND ALONG THE RUNNING DIRECTION AT APEX HANDLE(500g)ON THESTRENGTH TEST,TIME IS

30 SECONDS. 在推柄的先端沿运行方向加上 (500g) 力度测试, 时间

30 秒. No damage (Electrical and mechanical) 电气和机械性能正常. 7.4 Stem Pull Strength 手柄拉拔强度 Break by a pull force applied opposite to the direction of stem operation. 在推柄动作方向反向垂直施加拉力, 使其破 坏的程度. 500gf Min 7.6 Life Test 寿命测试 AN ACTUATOR SHALL BE WITH A THRUST OF NO GREAT THAN

1 TIMES SWITH POWER TO

10000 CYCLES AT A SPEED OF

30 CYCLES FOR

1 MIN. 操作者以每分钟

30 次的频率, 施加不大于开关

1 倍的推力做

10000 次无负荷测试. 1) CONTACT RESISTANCE SHALL BE 500m? MAX. 2) LIFETIME:10000 次1) 接触电阻?超于500m?. 2)寿命:10000 次8. Environmental Performance/环境性能: Item 项目 Description 项目描述 Test Condition 测试条件 Requirement 规格要 求8.1 Cold test 耐寒性 (1) Temperature : - 25±3℃ 温度:- 25±3℃ (2) Duration of test: 96h 持续时间:96 小时 (3) Take off a drop water 去掉水珠 (4) Standard conditions after test : 1h 试验后的放置条件:1 小时 THERE SHALL BE NO DAMAGE ONAPPEARANCE. MECHANICAL AND ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED. 外观无异常,满足于机 械,电气性能 Product Specification P/N: CSL903610D01 DOC. No.: KH-PS1704-53 Rev.: A Page: 7/9 Confidential All Right Reserved COPYRIGHT Kaihua Electronics Co.,LTD 8.2 Heat test 耐热性 (1) Temperature : 80±2℃ 温度:80±2℃ (2) Duration of test: 96h 持续时间:96 小时 (3) Take off a drop water 去掉水珠 (4) Standard conditions after test : 1h 试验后的放置条件:1 小时 THERE SHALL BE NO DAMAGE ONAPPEARANCE. MECHANICAL AND ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED. 外观无异常,满足于机 械,电气性能 8.3 Temperature cycle 温度循环 (1) Test cycles: