PDF《产品规格书》

平行地插入、锁紧、拔出. Insert and extract applicable FFC at the speed rate of 25±3 mm/minute. 锁紧力 Locking 1.96*n (N) Max. 拔出力 Withdrawal 0.49*n (N) Min. 6. 物理性能 PHYSICAL PERFORMANCE No. 项目 ITEM 试验方法 TEST METHOD 规格 SPECIFICATION 6.1 插拔耐久性 Durability 不通电状态下,以每分

10 次,插拔

30 次Connectors shall be mated and unmated at a speed of

10 times/min.without current applied . Number of mating and unmating/30 times. 接触电阻 Contact resistance: 0.03Ω MAX Page

5 of

8 产品规格书 Product Specification 编号Serial number PS2052 版本号Version Number

5 产品名称 Product Name TJC1008-30P 扁平电缆连接器 TJC1008-30P Flat Cable Connector 产品编码 Part Number 111.8255 6.2 振动 Vibration 遵循 JISC0040 标准,所有触点应串联在一 起,并加以 DC

100 毫安电流 In accordance with JIS C

0040 all contacts shall be connected in series and DC

100 mA shall be applied. 周期 Frequency:10~55~10 Hz/min 振幅 Maximum amplitude: 1.5mm 方向 Direction: X,Y,Z(3 Direction) 时间Duration: 2h per each direction total 6h 瞬断 Discontinuity :

1 μs MAX 外观 Appearance : 无损伤 No damage,loose part nor crack 接触电阻 Contact resistance: 0.03Ω MAX 6.3 冲击 Shock 遵循 JISC0041 标准,所有触点应串联在一 起,并加以

100 毫安电流 In accordance with JIS C 0041,all contacts shall be connected in series and DC

100 mA shall be applied. 最大加速度 Maximum acceleration :490m/s

2 (50G);

半波正弦波 Half sine wave. (持续时间 Duration:11ms) 方向 Direction :3 directions(X,Y,Z) 回数Number :3 times per each direction. 瞬断 Discontinuity:

1 μs MAX 外观 Appearance : 无损毁 No damger,loose part nor crack 接触电阻 Contact resistance :0.03Ω MAX 6.4 可焊性 Solderability 把试验样品需要焊接的部位浸入焊锡炉中 (锡炉温度 245±2℃) ;

3±0.5 秒钟 Soldering Time: 3±0.5 second Solder Temperature: 245±2℃ 上锡率≥95%: 95% of immersed area must show no voids, pin holes 6.5 耐焊接热 Resistance to soldering heat 把试验样品需要 SMT 回流焊炉过炉,按照无 铅制程曲线(最高温度 250±5℃,10±1 秒钟) ,在正常条件下恢复

2 小时. Soldering Time: 10±1 second Solder Temperature: 250±5℃ 外观:无损伤 Appearance::No Damage Page

6 of

8 产品规格书 Product Specification 编号Serial number PS2052 版本号Version Number

5 产品名称 Product Name TJC1008-30P 扁平电缆连接器 TJC1008-30P Flat Cable Connector 产品编码 Part Number 111.8255 7.电气的性能 ELECTRICAL PERFORMANCE No. 项目 ITEM 试验方法 TEST METHOD 规格 SPECIFICATION 7.1 耐电压 Dielectric withstanding voltage 遵循 MIL-STD-202F m301 标准, 应在端子之 间,及端子与壳体之间加以

500 V 交流电, 保持

1 分钟(漏电流

2 毫安) In accordance with MIL-STD-202F m301,AC

500 V shall be applied between contacts and between an individual contact and a case for

1 min.(Leak current

2 mA). 外观 Appearance 无火花及绝缘损坏 No flashover,sparkover nor dielectric breakdown. 7.2 绝缘电阻 Insulation resistance 遵循 MIL-STD-202F m302 标准, 应在端子之 间,及端子与壳体之间加以

500 V 直流电, 保持

1 分钟. In accordance with MIL-STD-202F m302,DC

500 V shall be applied between contacts and between an individual contact and a case for

1 min. 最初为 1000MΩ Initial:1,000 MΩ MIN 7.3 接触电阻 contact resistance 插配 FPC 线缆后,用小功率电路进行测试 Mate applicable FPC, measure by dry circuit. 接触电阻 Contact resistance: 0.03Ω MAX 7.4 温度上升 Temperature rise 触点应保持连接,温度上升应在无风条件下 测试. Contact shall be connected in series and temperature rise shall be measured under ........