PDF《BA-S-PL 840 G3》

产品优势 _ 这些模块兼容于 BackLED 安装支架 _ 与无透镜的系统相比,大大提高应用效率 _ 用于快速、简便地完成安装过程(螺栓式安装或卡装)的多种选项 _ 一致性好的白色光(标准颜色偏差与 SDCM 相当: <

3) _ 5年质保 产品特点 _ 与软性电缆连接 _ 保护级别(模块):IP66 _ 显色指数 R a : >

80 _ 使用寿命(L70/B50):50,000 h 产品数据表 BA-S-PL

840 G3 BackLED S Plus G3 | 招牌和背光照明用 LED 模块 应用领域 _ 招牌和灯光广告 _ 小型和/或扁平通道文字的背光照明 _ 用于密闭灯箱或轮廓文字的永久户外使用 __ 六月 13, 2019, 17:16:35 ? 2019, OSRAM GmbH.

版权所有. BA-S-PL

840 G3 页面 技术参数 电参数 标称电压 12.0 V 单链标称功率 30.0 W 单个 LED 模块的标称功率 0.33 W Accidental reverse input voltage protection up to

13 V 输入电压范围 12…13 V 电流类型 DC 光度数据 色温

4000 K 显色指数 Ra

80 EN 12464-1 标准光色 自然白色 LED 光色 白色 单个模块链的光通量

3510 lm 单个 LED 模块的光通量

39 lm 发光效率

116 lm/W 色彩匹配标准偏差 ≤3 sdcm 光参数 光束角

155 ° LED 模块信息 模块LED颗粒数

3 单个链中的 LED 模块数量

90 LED 模块的最小可操作数量

1 尺寸和重量 产品数据表 __ 六月 13, 2019, 17:16:35 ? 2019, OSRAM GmbH. 版权所有. BA-S-PL

840 G3 页面 长度

12454 mm 宽度 12.0 mm 高度 6.0 mm 产品重量 504.00 g 温度 工作温度范围 -25…65 °C 1) 仓储温度范围 -25…85 °C 1) T c 温度点 寿命 寿命

50000 h 更多的产品数据 产品说明 Modules perfectly matched to OSRAM OPTOTRONIC LED drivers (see relevant table)/对当前光测定数据和 重要的安全、安装和应用的信息,请查看 www.osram.com/led-systems/所有技术参数均适用于 全部模组.由于发光二极管制造过程的复杂性, LED光色、寿命等标称参数值均为统计数值, 而不对应个体 产品, 个体产品的实际参数值可能与标称值存在差异 . 功能 可调光 是 调光范围 1…100 % 认证与标准 能耗

34 kWh/1000h 能效等级 A+ 防护类型 IP66 标准 根据 IEC 62471标准/根据 IEC 60598-1标准/根据 EN 60529标准/根据 EN 62031标准/根据 EN 55015标准 /根据 EN 61547标准/ENEC 认证标志 C 认证 CE / ENEC / UL recognized component 物流数据 商品编码

940540399000 产品数据表 __ 六月 13, 2019, 17:16:35 ? 2019, OSRAM GmbH. 版权所有. BA-S-PL

840 G3 页面 保证 设备/配件 _ 可提供多种 OPTOTRONIC

12 V 电源 产品数据表 __ 六月 13, 2019, 17:16:35 ? 2019, OSRAM GmbH. 版权所有. BA-S-PL

840 G3 页面 DST_00.01 数据表文本 [calc.] _ Installation of LED modules (with power supplies) needs to be made under consideration of all valid regulations and norms. _ Installation by qualified electrician only. _ Please see the relevant application guides and instructions sheets for more detailed safety and mounting information. Additional information is available on request. _ Complies with IEC/EN

61547 _ Complies with IEC/EN 61000-3-2 _ Complies with EN 55015, CISPR

15 _ Complies with IEC/EN 61347-1 _ Complies with IEC/EN 61347-2-13 _ Parallel connection is mandatory for safe electrical operation. Serial connection of LED modules is stronly discouraged. Unbalanced voltage drop in serial connection can cause hazardous overload and damage the LED module. _ Electrical contact is achieved with the contact cables or the terminals of the module. Please refer to the technical data for maximum number of LED modules that can be operated on one control gear. _ In order to operate OSRAM LED modules safely, it is absolutely necessary to operate them with an electronically stabilized power supply that protects against short circuits, overload and overheating. _ In case other power supplies than OSRAM OPTOTRONIC are used, compliance to the neccessary operating parameters (voltage, current, power) has to be ensured. _ Pay attention to polarity! Wrong polarity can cause destruction or malfunction of the module. _ Conducting paths on the circuit board must not be damaged or destroyed during installation. _ The LED module itself and all its components must not be stressed mechanically. _ Operation in or under water is prohibited. _ To avoid mechanical damage, the LED modules have to be attached securely to the intended mounting surface. It is recommended to avoid heavy vibration. _ In case that the LED module is equipped with a pre-mounted double-sided adhesive tape, OSRAM assumes no liability and provides no guarantee for a permanent adherence of the modules to the surface. OSRAM recommends fixation of the modules by means of suitable screws. _ Complies with IEC 61347-1 cl. 18.3, cl. 18.4, IEC 60695-2-10, IEC 60695-11-5, IEC 60695-11-10 (classification V-0) _ All the technical parameters apply to the entire module. In view of the complex manufacturing process for light emitting diodes, the specified typical values for the technical LED parameters are merely statistical values that do not necessarily correspond to the actual technical parameters of an individual product;