PDF《注意事项》

Warning EN a DVP06XA-S2 is an OPEN-TYPE device.

It should be installed in a control cabinet free of airborne dust, humidity, electric shock and vibration. To prevent non-maintenance staff from operating DVP06XA-S2, or to prevent an accident from damaging DVP06XA-S2, the control cabinet in which DVP06XA-S2 is installed should be equipped with a safeguard. For example, the control cabinet in which DVP06XA-S2 is installed can be unlocked with a special tool or key. EN a DO NOT connect AC power to any of I/O terminals, otherwise serious damage may occur. Please check all wiring again before DVP06XA-S2 is powered up. After DVP06XA-S2 is disconnected, Do NOT touch any terminals in a minute. Make sure that the ground terminal on DVP06XA-S2 is correctly grounded in order to prevent electromagnetic interference. FR a DVP06XA-S2 est un module OUVERT. Il doit être installé que dans une enceinte protectrice (boitier, armoire, etc.) saine, dépourvue de poussière, d'

humidité, de vibrations et hors d'

atteinte des chocs électriques. La protection doit éviter que les personnes non habilitées à la maintenance puissent accéder à l'

appareil (par exemple, une clé ou un outil doivent être nécessaire pour ouvrir a protection). FR a Ne pas appliquer la tension secteur sur les bornes d'

entrées/Sorties, ou l'

appareil DVP06XA-S2 pourra être endommagé. Merci de vérifier encore une fois le c?blage avant la mise sous tension du DVP06XA-S2. Lors de la déconnection de l'

appareil, ne pas toucher les connecteurs dans la minute suivante. Vérifier que la terre est bien reliée au connecteur de terre afin d'

éviter toute interférence électromagnétique. X Introduction ? Model Explanation &

Peripherals z Thank you for choosing Delta DVP series PLC. DVP06XA-S2 is able to receive

4 points of analog input signals (voltage or current) and convert them into 12-bit/14-bit digital signals. DVP06XA-S2 receives

2 groups of 12-bit digital data from the PLC MPU and converts them into

2 points of analog signals for output (in voltage/current). There are

49 16-bit control registers (CR) in DVP06XA-S2, and the data in it can be read and written by using FROM/TO instructions in DVP Slim series PLC MPU program. z The user can select voltage or current input by wiring. Range of voltage input: ±10VDC (12-bit resolution: 5mV;

14-bit resolution: 1.25mV). Range of current input: ±20mA (11-bit resolution: 20μA;

13-bit resolution: 5μA). z The user can also select voltage or current output by wiring. Range of voltage output: 0V ~ 10VDC (default) (12-bit resolution: 2.5mV). Range of current output: 0mA ~ 20mA (12-bit resolution: 5μA). ? Product Outline and Terminal Layout Terminal Layout Figure

1 3.00 3.00 60.00 3.40 60.00

1 2

3 14

4 5

6 8

10 3

7 9 I4 + V4 + V1 + I1 + C OM

1 I2 + V2 + C OM

2 C OM

4 I3 + V3 + C OM

3 I5 + V5 + I6 + V6 + C OM C OM D A ER RO R P O WER 90.00 3.00 25.20 90.00

12 11

13 Unit: mm Figure

2 V1+ I1+ C OM1 V2+ I2+ C OM2 V3+ I3+ C OM3 V4+ I4+ C OM4 V5+ I5+ C OM V6+ I6+ C OM 1. POWER LED indicator, ERROR LED indicator, and RUN LED indicator 2. Model 3. DIN rail clip 4. Terminals 5. Arrangement of the terminals 6. Locating hole on the extension module 7. Nameplate 8. Connector on the extension module 9. Mounting clip on the extension module 10. Groove for a DIN rail (35mm) 11. RS-485 port 12. Groove on the extension module 13. Power connector 14. Connector on the extension module ENGLISH ? External Wiring V1+ I1+ CH1 V4+ CH4 *3 *2 24V 0V DC24V DC/DC +15V -15V AG CH1 1M AG 1M

250 CH4 1M AG 1M

250 -10 V~ +10 V -20 mA~+

20 mA COM1 COM4 Voltage input Current input Connected to on a power module Shielded cable*1 Shielded cable

1 * Third type of ground (Impedance: Less than

100 ) I4+ converter Vol ta ge output -10V ~ +10V *5 Inve rter, recorde r, proportioni ng valve V5+ I5+ V6+ CH6 24V 0V DC24V DC/DC +15V -15V AG COM Shilded cable*4 I6+ Current outp ut 0m A ~ 20m A Inve rter, recorde r, proportioni ng valve CH5 CH6 CH5 COM *6 Connected to on a power module Third type of ground (Impedance: Less than

100 ) converter Shilded cable*4 *1: Please isolate the analog input signal cables from other power cables. *2: If the module is connected to a current signal, the terminals V4+ and I4+ have to be short-circuited. *3: If the ripple in the input voltage results in the noise interference with the wiring, please connect the module to the capacitor having a capacitance in the range of 0.1 μF to 0.47 μF with a working voltage of

25 V. *4: Please isolate the analog output signal cables from other power cables. *5: If the ripple is large for the output terminal of the load and results in the noise interference with the wiring, please connect the module to the capacitor having a capacitance in the range of 0.1 μF and 0.47 μF with a working voltage of

25 V. *6: Please connect on a power module and on DVP06XA-S2 to the ground, and then ground the ground or connect the ground to a distribution box. Y Specifications Mixed analog/digital (A/D) module Voltage input Current input Power supply voltage 24VDC (20.4VDC ~ 28.8VDC) (-15% ~ +20%) Analog input channel

4 channels per module Analog input range ±10V ±20mA Digital data range ±2,000 (12 bits);

±8,000 (14 bits) ±1,000 (11 bits);

±4,000 (13 bits) Resolution

12 bits (1LSB=5mV)

14 bits (1LSB=1.25mV)

11 bits (1LSB=20μA)

13 bits (1LSB=5μ) Input impedance 200K? and above 250? Overall accuracy ±0.5% of full scale of 25°C (77°F). ±1% of full scale during

0 ~ 55°C (32 ~ 131°F). Response time 3ms * channels Isolation method An analog circuit is isolated from a digital circuit, but the analog channels are not isolated from one another. Absolution input range ±15V ±32mA Digital data format 2'

s complement of a 16-bit value Average function Yes (CR#2 ~ CR#5 can be set and the range is K1 ~ K20) Self diagnostic function self detection Upper bound and lower bound detection per channel Mixed digital/analog (D/A) module Voltage output Current output Analog signal output channels

2 channels per module Analog output range

0 ~ 10V ±10V

0 ~ 20mA Digital data range

0 ~ 4,000 (12 bits) ±2,000 (12 bits)

0 ~ 4,000 (12 bits) Resolution

12 bits (1LSB=2.5mV)

12 bits (1LSB=5mV)

12 bits (1LSB=5μA) Overall accuracy ±0.5% of full scale of 25°C (77°F). ±1% of full scale during

0 ~ 55°C (32 ~ 131°F). Output impedance 0.5? or lower Response time 3ms * channels Max. output current 10mA (1K? ~ 2M?) - Tolerance carried impedance -

0 ~ 500? Digital data format 2'

s complement of a 16-bit value Protection Voltage output has short circuit protection but long period of short circuit may cause internal wiring damage and current output break. Communication mode (RS-485) MODBUS ASCII/RTU Mode. Communication baud rate of 4,800/9,600/19,200/38,400 /57,600/115,200. For the ASCII mode, date format is

7 bits, even,

1 stop bit (7, E, 1). For the RTU mode, date format is

8 bits, even,

1 stop bit (8, E, 1). The RS-485 is disabled when DVP06XA-S2 is connected in series with MPU. Mixed digital/analog (D/A) module Voltage output Current output Connect to DVP-PLC MPU in series When DVP06XA-S2 modules are connected to an MPU, the modules are numbered from 0-7.

0 is the closest to the MPU and

7 is the furthest. The Maximum number of modules is

8 modules and they do not occupy any digital I/O points of the MPU. ? Others Power supply Maximum power consumption 2W at 24VDC (20.4VDC ~ 28.8VDC) (-15% ~ +20%), supplied by external power. Environment Operation/storage Operation: 0°C ~ 55°C (temperature);

5 ~ 95% (humidity);

pollution degree 2. Storage: -25°C ~70°C (temperature);

5 ~ 95% (humidity). Vibration/shock immunity International standards: IEC 61131-2, IEC 68-2-6 (TEST Fc)/IEC 61131-2 &

IEC 68-2-27 (TEST Ea) Z CR (Control Register) b15 b14 b13 b12 b11b10 b9 b8 b7 b6 b5 b4 b3 b2 b1 b0 CR # RS-485 parameter address Latched Register name CH6 CH5 CH4 CH3 CH2 CH1 #0 H'

40C8 R Model type System used, data length is

8 bits (b7 ~ b0). DVP06XA-S2 model code = H'

D4 User can judge whether the extension module exists by using a program to read the model code. #1 H'

40C9 R/W Input/Output mode setting Input mode setting: (CH1 ~ CH4) Mode 0: input voltage mode (-10V ~ +10V). Mode 1: input voltage mode (-6V ~ +10V). Mode 2: input current mode (-12mA ~ +20mA). Mode 3: input current mode (-20mA ~ +20mA). Mode 7: none use. Output mode setting: (CH5 ~ CH6) Mode 0: output voltage mode (0V ~ 10V). Mode 1: output voltage mode (2V ~ 10V). Mode 2: output current mode (4mA ~ 20mA). Mode 3: output current mode (0mA ~ 20mA). CR#1: b11 ~ b0 are used to set

4 internal channels working mode of analog input module (AD). b12 ~ b15 are used to set

2 channels working mode of analog output module (DA). Every channel has four modes that can be set individually. For example: if setting CH1 to mode

0 (b2 ~ b0=000), CH2 to mode

1 (b5 ~ b3=001), CH3: mode

2 (b8 ~ b6=010), CH4: mode

3 (b11 ~ b9=011), b0 ~ b11 need be set to H'

688. If setting CH5: mode

2 (b13 ~ b12=10), CH6: mode

1 (b15 ~ b14=01), b12 ~ b15 need be set to H'

6. Factory Setting is H'

0000. #2 H'

40CA R/W CH1 average number #3 H'

40CB R/W CH2 average number #4 H'

40CC R/W CH3 average number #5 H'

40CD R/W CH4 average number Number of readings used for average temperature on channels CH1 ~ CH4 The setting range is K1 ~ K20 and the factory setting is K10. Please note that users can only set CR#2 ~ CR#5 once. If they set CR#2 ~ CR#5 several times, average values can not be gotten. #6 H'

40CE R Average value of CH1 input signal #7 H'

40CF R Average value of CH2 input signal #8 H'

40D0 R Average value of CH3 input signal #9 H'

40D1 R Average value of CH4 input signal Display average value of CH1 ~ CH4 input signal. #10 H'

40D2 R/W CH5 output signal value #11 H'

40D3 R/W CH6 output signal value Output value of CH5 ~ CH6 The factory setting is K0 and the unit is LSB. #12 H'

40D4 R Present value of CH1 input signal #13 H'

40D5 R Present value of CH2 input signal #14 H'

40D6 R Present value of CH3 input signal #15 H'

40D7 R Present value of CH4 input signal Display present value of CH1 ~ CH4 input signal #16 H'

40D8 R/W DA: ±10V AD: switching to the 12-bit/14-bit mode (Factory setting: H0000) bit12~15: switching to the ±10V mode of DA bit12: switching to the ±1........