PDF《PLN-20》

SPECIFICATION MODEL PLN-20-18 PLN-20-24 PLN-20-36 DC VOLTAGE RATED CURRENT CURRENT RANGE RATED POWER OUTPUT LINE REGULATION LOAD REGULATION SETUP TIME VOLTAGE RANGE Note.

4 FREQUENCY RANGE POWER FACTOR EFFICIENCY(Typ.) AC CURRENT INPUT INRUSH CURRENT(Typ.) LEAKAGE CURRENT SAFETY STANDARDS WITHSTAND VOLTAGE ISOLATION RESISTANCE WORKING TEMP. WORKING HUMIDITY STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION MTBF DIMENSION OTHERS NOTE PACKING OVER CURRENT Note.5 SHORT CIRCUIT OVER VOLTAGE OVER TEMPERATURE 18V 13.5 ~ 18V 24V

18 ~ 24V 36V 1.1A 0.8A 0.55A

0 ~ 1.1A

0 ~ 0.8A

0 ~ 0.55A 19.8W 19.2W 19.8W 3.0Vp-p 3.0Vp-p 3.0Vp-p ±3.0% ±10% ±10% 500ms / 230VAC 2000ms / 115VAC at full load

90 ~ 277VAC 127~392VDC

47 ~ 63Hz 0.4A/115VAC 0.2A/230VAC 0.15A/277VAC COLD START 35A(twidth=40 s measured at 50% Ipeak) at 230VAC μ 0.5mA / 240VAC

95 ~ 110% Protection type : Constant current limiting, recovers automatically after fault condition is removed Hiccup mode, recovers automatically after fault condition is removed. Compliance to EN61000-4-2,3,4,5,6,8,11;

EN61547, light industry level, criteria A I/P-O/P:3.75KVAC I/P-O/P:100M Ohms/500VDC /

25 / 70%RH ℃ -30 ~ +60 (Refer to Derating Curve ) ℃

20 ~ 90% RH non-condensing -40 ~ +80 ,

10 ~ 95% RH ℃ ± ℃ ℃ 0.06%/ (0 ~

50 )

10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes 20W Single Output LED Power Supply Universal AC input / Full range(up to 277VAC) Protections:Short circuit/Over current/Over voltage/Over temperature Cooling by free air convection Built-in constant current limiting circuit with adjustable OCP level Fully isolated plastic case Built-in active PFC function IP64 design for indoor or outdoor installations Small and compact size Class power unit, no FG Ⅱ 100% full load burn-in test High reliability,low cost Suitable for Dry / Damp locations Suitable for LED lighting and moving sign applications

2 years warranty Features : PLN-20 series RIPPLE &

NOISE (max.) Note.2 VOLTAGE TOLERANCE Note.3 ENVIRONMENT SAFETY &

EMC PROTECTION IEC61347-1, IEC61347-2-13, TUV EN61347-1, EN61347-2-13, UL8750,CSA C22.2 No. 250.0-08,J61347-1, J61347-2-13, IP64 approved PLN-20-48 48V 0.42A

0 ~ 0.42A 20.2W 3.8Vp-p CURRENT ADJ. RANGE 75% ~ 100%

36 ~ 48V

27 ~ 36V 148.5*38.5*28mm (L*W*H) 643.6Khrs min. MIL-HDBK-217F (25 ) ℃ 0.18Kg;

60pcs/12.8Kg/0.9CUFT PLN-20-12 12V

9 ~ 12V 1.6A

0 ~ 1.6A 19.2W 2.5Vp-p Protection type : Shut off o/p voltage, clamping by zener diode

19 ~ 22V

27 ~ 34V

41 ~ 46V

54 ~ 60V

14 ~ 16V 81% 82% 83% 83.5% 80% 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and

25 of ambient temperature. ℃ 2. Ripple &

noise are measured at 20MHz of bandwidth by using a

12 twisted pair-wire terminated with a 0.1uf &

47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. Derating may be needed under low input voltage, please check the static characteristic for more details. 5. lease refer to DRIVING METHODS OF LED MODULE . P 6. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again. 7. Direct connecting to LEDs is suggested, but is not suitable for using additional drivers. 8. To fulfill requirements of the latest ErP regulation for lighting fixtures, this LED power supply can only be used behind a switch without permanently connected to the mains. M M IP64