XLS《Sheet1》

"附件",,

,,

"国内投资项目不予免税的进口商品目录(2008年调整)",,

,,

,,

,,

"编号","税则号列","设备名称","技术规格(调整后)","备注" "通用设备",,

,,

"一",,

"柴油机",,

"1","840820840890","柴油机(船用柴油机见后)","额定功率≤300kw", "二",,

"泵",,

"1","8413110084131900","计量泵","流量≤8200L/h", "2","841350","往复泵","所有规格","税号调整" "3","84137091","电动潜油泵","所有规格","税号调整" "4","84137091","潜水电泵","所有规格","税号调整" "5","841360","回转泵","所有规格","税号调整" "6","841370","离心泵","转速≤20000r/min,流量≤200m3/h,扬程≤3000m","税号调整" "7","84138100","大型污水泵","流量≤6.

0m3/s,扬程≤21m", "8","84138100","电磁泵、喷射泵、乳化液泵、气体压力泵","所有规格", "9","84138200","液体提升机","所有规格", "10","84141000","真空泵","所有规格", "11","84142000","手动或脚踏式空气泵","所有规格", "三",,

"风机、压缩机",,

"1","84145990","轴流式风机","所有规格", "2","84145930","离心式风机","流量≤1800m3/min,压升≤19Kpa", "3","84148090841430","轴流压缩机","流量≤10000m3/min,轴功率≤51000kw", "4","84143084148090","离心式压缩机","所有规格(流量>5000m3/min或出口压力>50Mpa除外)","税号调整、技术规格调整" "四",,

"制冷装置",,

"1","84186920","冷水机组","所有规格", ,"84186990",,

, "2","84186920","离心式制冷机组","输出功率≤3000kw", "3","84186920","螺杆式制冷机组","所有规格", "五",,

"气体分离装置及关键设备",,

"1","8419601184196019","制氧机","制氧量≤65000Nm3/h(Nm3/h指名义工况下立方米每小时,即标立方)","税号调整、技术规格调整" "2","84194020","气体分离设备用精馏塔","所有规格", "3","84195000","气体分离设备用板翅式换热器","所有规格", "4","84213990","气体分离设备用分子筛吸附器","所有规格","税号调整" "5","84798990","气体分离设备用膨胀机","流量≤40000Nm3/h,进口压力≤5Mpa(Nm3/h指名义工况下立方米每小时,即标立方)", "六",,

"分离设备",,

"1","842121908421220084212990","真空带式过滤机","过滤面积≤110O", "2","84211920","固液、液液分离机","所有规格", ,"84211990",,

, "3","842119","螺旋沉降式离心机","转鼓直径≤800mm", "4","842119","活塞推料离心机","转鼓直径≤800mm", "5","84212990","真空转鼓滤碱机","所有规格", "6","84212990","转台式过滤机","过滤面积≤132O", "7","84212990","盘式过滤机","过滤面积≤120O", ,"84213990",,

, "8","84212","液体过滤、净化机及反渗透装置(除以上分离设备以外)","单台液体处理量≤200t/h","税号调整、技术规格调整" "七",,

"起重机械",,

"1","8425110084251900","提升机","滚筒直径≤5.5m","税号调整、技术规格调整" "2","84253190","电动葫芦","所有规格", "3","8426112084261190","单梁起重机","所有规格","税号调整" "4","8426112084261190","双梁桥式起重机","冶金:起重量≤400t;

其他:起重量≤1200t","税号调整" "5","84261200","带胶轮移动式吊运架及跨运车","所有规格", "6","84262000","塔式起重机","起重力矩≤1000t・m", "7","84263000","门座式起重机(门座式轮胎起重机见下)","所有规格", "8","84263000","门座式轮胎起重机","起重量≤50t", "9","84264910","履带式起重机","起重量≤1000t","技术规格调整" "10","84283200","斗式提升机","所有规格", "11","84253190","水利启闭机","所有规格", "12","84281090","升船机","所有规格", "八",,

"钻采设备",,

"1","84304111843041198501585016850285371090","石油及天然气钻探机(采矿钻机、工程钻机、其他钻探机见后)","钻探深度≤9000m(包括钻机配套发电机、电动机、电控制系统)","税号调整、设备名称变更" "2","84306990","修井机","额定载荷≤150t", "3","84798990","采油气井口装置","双油管压力≤70Mpa;

单油管压力≤105Mpa", "九",,

"草坪、公园、运动场机动割草机","", "1","84331100","草坪、公园、运动场机动割草机","所有规格", ,"84331900",,

, "十",,

"机床及锻压、铸造设备",,

"

(一)",,

"非数控机床",,

"1","8456845784588459846084618462846384648465","非数控机床","所有规格", "

(二)",,

"数控机床",,

"1","84561000","数控激光加工机","≤3轴联动","技术规格调整" "2","8456901084615000","数控切割机","等离子切割机:板厚≤40mm;

水切割机:≤3轴联动;

其他数控切割机:所有规格","技术规格调整" "3","84571030","龙门式加工中心","0.006mm, 重复定位精度≥0.004mm, 快移速度≤40m/min,4轴联动,工作台1250mm","技术规格调整" "7","8458110084589100","车削中心","重复定位精度≥0.004mm, 主轴端径向圆跳动≥0.001mm,加工圆度>0.001mm", "8","84581100","数控重型卧式车床","最大加工工件直径D≤4000mm,工件长度≤20000mm, 加工圆度≥5*10-6*Dmm","技术规格调整" "9","84589100","数控重型立式车床","最大加工工件直径D≤16000mm, 定位精度>0.015mm/2m,加工圆度>0.01mm","技术规格调整" "10","8458110084589100","数控车床","重复定位精度>5μm, 加工圆度≥3*10-6*Dmm(D为最大加工工件直径)","技术规格调整" "11","84596110","数控龙门铣床","工作台宽度0.006mm(全程), 重复定位精度>0.004mm,≤4轴联动","税号调整、设备名称变更" "13","846021108460212084602190","数控重型磨床","工件直径≤1600mm,加工圆度>0.001mm,微量进给>0.0001mm","税号调整" "14","84601100","数控平面磨床","定位精度>0.006mm(全程),重复定位精度>0.003mm(全程),平面度>0.002mm/1000mm,龙门宽≤3500mm", "15","84602110846021208460219084603100","数控磨床(含内圆、外圆、端面外圆、万能、无心、轴承、刃磨等),专用除外","定位精度>0.006mm,重复定位精度>0.003mm,加工圆度>0.0005mm,砂轮线速度≤60m/s","设备名称变更" "16","846021","数控凸轮轴磨床","工件最大回转直径≤Φ250mm,砂轮线速度≤60m/s(单砂轮)","税号调整" "17","846021","数控曲轴磨床","工件直径≤Φ630mm,砂轮线速度≤60m/s;

定位精度>0.005mm,重复定位精度>0.002mm","税号调整、技术规格调整" "18","84614010","数控重型滚齿机","立式:工件直径≤Φ8000mm,模数m≤30mm;

卧式:工件直径≤Φ2000mm,模数m≤30mm;

其他:所有规格", "19","84614010","数控齿轮加工机床","工件直径:15-800mm,模数:2-8mm,≤3轴联动,精度等级>5级", "20","84593100","数控铣镗床","镗杆直径10m或板厚>120mm*板宽>3200mm除外)","技术规格调整" "8","8462219084622990","折边机","所有规格", "9","846231108462312084623190","数控板带剪切机床","板厚*宽≤12*4000mm","税号调整" "10","8462319084623990","棒料剪断机","公称压力≤500t", "11","8462419084624900","联合冲剪机","板厚≤30mm,冲孔力