编辑: ACcyL 2016-11-12
压管机使用说明书 适用范围: 该压管机是在压力作用下使金属接头产生变形,从而平稳、精确地扣压在胶管上的专用设备、如(液压机械、注塑机、挖机、装载机、吊机、汽车空调管),从而平稳、精确地扣压在胶管上的专用设备、如(液压机械、注塑机、挖机、装载机、吊机、汽车空调管),是液压机械厂,挖机维修点,的必选设备,本机自1999年开始投入市场,2年内故障率不到1%,是一款性能稳定,简单易用,经济型的压管机 .

Applies range:the pressure tube machine is in pressure role Xia makes metal joints produced deformation, thus smooth, and precise to withheld in glue tube Shang of dedicated equipment, and as (hydraulic mechanical, and injection machine, and dug machine, and mount machine, and hanging machine, and car air conditioning tube), is hydraulic machinery factory, dug machine maintenance points, of will selected equipment, this machine since

1999 began inputs market,

2 years within fault rate not to 1%, is a paragraph performance stable, simple easy, budget of pressure tube machine. 产品技术参数如下: 1.压管通径:Φ6~Φ51mm(最大2英寸,最小2分) 2.电机功率:3KW 3.额定电压:三相AC380V或单相AC220V 4.最高油压:31.5Mpa 5.油泵流量:2.5ML/REV 6.最大扣压力:≥3000KN 7. 随机配套模具: 1/4 3/8 1/2 5/8 3/4 1″ 1,1/4 1,1/2 2″ 8. 外型尺寸:700mm*450mm*700mm(L*W*H) 9. 整机重量(不含油):200KG 10.可装50升68#抗磨液压油.(2小桶,13KG一桶) Product technical parameters are as follows: 1. pipe diameter: φ 6~ 51mm (maximum

2 inch, min

2 min) 2. motor power: 3KW 3. rated voltage: three-phase AC380V or single-phase AC220V 4. MTP 31.5Mpa 5. oil pump flow rate: 2.5ML/REV 6. maximum deduction pressure: ≥ 3000KN 7. Random supporting mold: one-fourth three-eighths one-second three-fourths 1,1/4 1,1/2 your 1/2 8. Dimensions: 700mm*400mm*700mm (L*W*H) 9. Weight (without oil): the 200KG 10.50 litres 46# hydraulic oil.

一、工作原理 油泵在电机驱动下,输出液压油,推动扣压油缸内的柱塞向前运动,使柱塞、前缸盖上的两个内锥套推动具有对称锥面的模座径向收缩,实现模块对胶管的扣压.当收缩量达到标尺调定值时,扣压自动停止,电磁换向阀换向后,液压油进入两个开模油缸,推动扣压柱塞反向运动,模座在弹簧作用下带动模块复原. One, works under the pump and motor-driven, hydraulic oil output, push forward and withheld the piston in the cylinder movement, on the piston and cylinder head before the two symmetrical conical clamping sleeve push in radial shrinkage, realize the hose crimping module. When contraction ruler set value is reached, withheld automatically stops after the solenoid valve, hydraulic oil enters the two open mold oil cylinder, push withheld plunger reverse movement, clamping spring drive module recovery.

二、安装调试 1.???? 搬运:机器宜采用叉车搬运,并以机器底部受力,机身不允许倾斜.严禁搬抬锁头及标尺部位. 2.???? 安装:机器需水平固定于稳固的地基上,并作接地处理. 3.???? 注油:打开机壳,油箱中加入50L长城牌46#或68#抗磨液压油. 4.???? 接电:将电源线接在机器规定的电源上,点动电机观察旋向,电机旋向应与油泵所指方向一致. 5.???? 检查标尺:标尺位于油缸前端面上(见上图),用于调节扣压管套收缩量的大小.顺时针调整,收缩量减小;

逆时针调整,收缩量增大.标尺座靠三个螺钉上的弹簧弹力压在油缸端面上,用手拉动标尺(垂直油缸端面方向),标尺座应灵活离开油缸端面,松开后,靠弹簧弹力自动压紧在油缸上.开始扣压前,应仔细检查标尺伸缩是否灵活.不可将标尺用螺钉紧固在油缸上,否则会损坏标尺. 6.? 压力调整:机器系统最大压力为20Mpa,靠溢流阀调整.顺时针调整压力增大,逆时针调整压力减小.(出厂时已调好,必要时可以自行调整) 7.开模速度调整:开模速度的快慢,由分流阀控制,顺时针调整,开模速度加快,逆时针调整,开模速度减慢,但开模速度过快会使噪音增大.(出厂时已调好,必要时可以自行调整) Second, installation and commissioning 1. Handling: machines suitable for forklift handling and loading at the bottom of the machine, the fuselage tilting is not allowed. Lift lock and Rod parts is strictly prohibited. 2. installation: required level is fixed at the machine on a solid foundation and ground handling. 3. oiling: to open the Cabinet, added 50L to the tank wall 46# anti-wear hydraulic oils. 4. power: plug the power cord connected to the machine specified on the power supply, move the motor to observe rotation direction, and should be consistent with the oil pump in the direction of motor rotation direction. 5. check the rulers: ruler located on the cylinder head surface (pictured above), to adjust withholding tube shrink quantity sizes. Adjust clockwise, shrinkage decrease and counterclockwise adjustment, increased shrinkage. Ruler near the three screws on the spring force on the cylinder face, hand pulling rod (vertical end face of the cylinder orientation), rulers should be flexible and leave the cylinder face, untied, by spring force automatically pressed on the cylinder. Before you start withholding, you should carefully check the ruler scale is flexible. Rod screws must not be fastened in the cylinder, otherwise it will damage the ruler. 6. pressure adjustments: machine system Max pressure 20Mpa, relying on relief valve adjusted. Clockwise adjustment increases pressure, counterclockwise to adjust the pressure decreases. (Factory-tuned, can adjust if necessary) 7. the mould opening speed adjustment: mould opening speed of, shunt valve controls clockwise adjust the opening speed, counterclockwise to adjust opening slow, but die too fast will make noise to increase. (Factory-tuned, can adjust if necessary)

下载(注:源文件不在本站服务器,都将跳转到源网站下载)
备用下载
发帖评论
相关话题
发布一个新话题