编辑: 252276522 | 2019-07-04 |
38 8.2 隔震层设计
38 8.3 大跨屋盖结构设计
39 8.4 支承结构和地基基础设计
40 9 核电厂建筑
41 9.1 一般规定
41 9.2 隔震设计
41 9.3楼层反应谱
43 9.4 隔震层的要求
43 9.5橡胶隔震支座的检验规则
44 9.6地震监测与报警
44 10 多层砌体房屋
45 10.1 一般规定
45 10.2 隔震层设计
45 10.3结构设计
46 11 既有建筑和历史建筑的隔震加固设计
48 11.1 一般规定
48 11.2 既有建筑的隔震加固设计
48 11.3 历史建筑的隔震加固设计
50 12村镇民居建筑
51 12.1 一般规定
51 12.2 房屋隔震设计要点
51 附录A 复振型影响系数计算公式
54 附录B 隔震建筑抗震性能设计
55 附录C 隔震支座连接设计
58 附录D 隔震支座力学分析模型和基本力学性能要求
62 附录E 既有建筑加固墙体和柱的托换方法
66 本标准用词说明
70 引用标准名录
71 条文说明
72 Contents Chapter
1 General
1 Chapter
2 Terms and symbols
2 2.1 Terms
2 2.2 Symbols
3 Chapter
3 Basic Requirements 3.1 General
9 3.2 Sites, Soils and Foundations
9 3.3 Test and Observation
10 Chapter
4 Earthquake Action and Checking for Isolated Structures
11 4.1 General
11 4.2 Design Response Spectra and Ground Motion
11 4.3 Earthquake Action
13 4.4 Checking for Strength
17 4.5 Checking for Super-structure Deformation
20 4.6 Design for Isolation Layer
21 4.7 Requirements for Sub-structure
24 Chapter
5 Constructional Measures for Isolated Structures
26 5.1 General
26 5.2 Connection of Isolation Bearings and Structure
26 5.3 Connection of Super-structure and Outside
27 5.4 Pipeline Passing Through Isolation Layer
27 5.5 Structural Deformation Joint
27 5.6 Inspection Opening and Isolation Marking
27 Chapter
6 Requirements for Isolation Bearings
29 6.1 General
29 6.2 Performance and Test Requirements
29 6.3 Connection
29 Chapter
7 Multi-Story and Tall Buildings
30 7.1 General
30 7.2 Design of Isolation Layer
31 7.3 Requirements for Structural Design
32 Chapter
8 Long-span Roof Buildings
38 8.1 General
38 8.2 Design of Isolation Layer
38 8.3 Requirements for Long-span Roof Structure Design
39 8.4 Requirements for Supporting Structure and Foundation
40 Chapter
9 Nuclear Power Plants
41 9.1 General
41 9.2 Isolation Design
41 9.3 Floor Response spectra
43 9.4 Requirements for Isolation Layer
43 9.5 Test Requirements for Rubber Bearings
44 9.6 Earthquake Monitoring and Warning
44 Chapter
10 Multistory Masonry Buildings
45 10.1 General
45 10.2 Design of Isolation Layer
45 10.3 Requirements for Structural Design
46 Chapter
11 Seismic Isolation Retrofit for Existing and Historic Buildings
48 11.1 General
48 11.2 Requirements for Existing Buildings
48 11.3 Requirements for Historic Buildings
50 Chapter
12 Rural Residential Buildings
51 12.1 General
51 12.2 Essentials in Design of Seismically Isolated Rural Residential Buildings
51 Appendix A Performance-Based Design of Isolated Building
54 Appendix B Formula of Influence Coefficient of Complex Vibration Modes
55 Appendix C Design of Connection of Isolation Bearings
58 Appendix D Mechanical Analysis Model and Requirements of Isolation Bearings
62 Appendix E Underpinning Method for Reinforcing wall and Column of Existing Building
66 Explanation of Wording in This Code
70 List of Quoted standards
71 Explanation of Provisions