PDF《E6B3-CWZ5G》

? OMRON Corporation

2012 All Rights Reserved.

? OMRON Corporation

2012 All Rights Reserved. E6B3-CWZ5G 旋转编码器 接线 E6B3-CWZ5G (+15% ) 电源电压 消费电流 输出状态 最高响应频率 输出相位差 起动转矩 惯性力矩 允许最高转速 输出容量 环境温度 环境湿度 轴允许力 输出电压:VH=Vcc-3V(IO=30mA) VL=2V以下(IO=-30mA) 输出电流:±30mA 100kHz A相、B相位差 90±45 10mN m以下 1*10-6 kg m2 以下 6000r/min -10~+70℃ 35~85%RH 径向……80N 轴向……50N 规格E6B3-CWZ5G 线色 端子名 褐黑白橙蓝0V 电源(+Vcc) 输出A相 输出B相 输出Z相-10% Model E6B3-CWZ5G ROTARY ENCODER Precautions for Safe Use Precautions for Correct Use

1 Since the product consists of high-precision components, handle it with utmost care.

2 Be careful not to expose the product to water or oil.

3 Be sure to turn off the power supply before wiring.If the output line contacts the power supply line while the power is being supplied,the output circuit may be damaged.

4 If the product is mounted and wired with a cord,do not pull the cord with force greater than 29.4 N.

5 Be careful not to apply excessive load to the shaft. Excessive load may cause the product break. Especially when linking with a chain,timing belt, or gears, connect a separate bearing before the coupling to the product.

6 If an installation error such as misalignment is too large,(in case using the coupling or without coupling) the shaft will be subjected to an excessive load which will damage it or shorten its service life.Be careful when installing.

7 When inserting the shaft in the coupling,do not use excessive force (by striking it with hammer,for example).

8 When installing or removing the coupling,do not apply an excessive being,compressing,or tensile force. OUTLINE DRAWING MOUNTING RATING OUTPUT CIRCUIT DIAGRAM Item E6B3-CWZ5G Complementary output 100kHz Supply voltage Current consumption

12 to 24V DC ( 15% ) 100mA max. Output circuit configuration Output capacity Maximum response frequency Phase different of output Starting torque Moment of inertia Slewing speed Shaft loading Ambient temperature Ambient humidity Output resistance: H level output voltage: Vcc-3V min.(at output current:+30mA) L level output voltage: 2V max. (at output current:-30mA) Output cerrent:±30mA max.

90 45 between output A and output B 10mN m

1 10-6 kg m2 6000r min Radial : 80N max. Axial : 50N max.

10 to

70 35 to 85%RH 10% DC12~24V 类型 规格 Type 100mA以下 互补输出 使用说明书 感谢您使用欧姆龙产品.以下主要记载安装和使用本产品过 程中需注意事项. 使用本产品前,请仔细阅读本说明书,充分了解产品. 为了您的方便,请妥善保管好本说明书. 输出回路图 安全上的要点 (1)使用时请不要超过额定电压范围.如施加额定电 压以上的电压时,会引起破裂和烧损. (2)高压线和动力线并行连线时,会因感应而发生误 动作或破损,所以请分开连线. (3)使用电源如发生浪涌,请在电源间接上浪涌吸收 器.为了避免干扰,请尽量在短距离之内连线. (4)在接通电源或切断电源时,容易发生错误脉冲, 所以请在接通电源1秒后、及切断电源1秒前使用. (5)需注意电源极性等,不能错误连线,以免引起破 裂和烧损. (6)注意不能让负载短路,以免引起破裂和烧损. (7)请不要在可燃性、爆炸性的环境下进行使用. (8)请不要拆卸、修理、改造本产品. 正确使用方法 (1)旋转式编码器是由紧密部件构成的,因此使用时 要非常小心,不能跌落,以免损伤功能. (2)使用时请不要让水和油滴落在主体上. (3)连线时要在电源切断的状态下进行.电源ON时, 输出线如接触电源,会引起输出回路破损. (4)固定本体、进行导线连线时,请注意导线的拉伸 力度不要超过29.4N. (5)请勿往轴上施加过大的载荷,以免引起产品破损. 用链条、传送带及齿轮连接时,先通过其他轴承, 再用耦合器与编码器结合. (6)如果安装误差大(偏心、偏角),就会有过大的 负载加在轴上,从而造成损坏或者缩短其使用年 限. (7)当耦合器插入轴时,请不要用锤子敲击等增加撞 击力. (8)安装、拆卸耦合器时,请勿进行不必要的弯曲、 压缩和拉伸. 外形尺寸图 安装尺寸 类型和规格 外部接线时,请注意不要错误连线. Thank for you selecting OMRON product.This sheet pri- marily describes precautions required in installing and operating the product. Before operating the product,read the sheet thoroughly to acquire sufficient knowledge of the product.For your con- venience,keep the sheet at your disposal. INSTRUCTION SHEET 安全上的注意 警告表示的意思 警告表示 如果不正确使用的话,有可能引起轻伤、中等 程度的伤害还有可能带来同样重大的物质损害. 注意 注意 通电状态下请勿拆开本产品.如触及内部会造成触电伤亡. 1)Do not use the product in excess of the rated voltage. Applying voltages beyond the rated voltage range may cause the product to breakor burn. 2)Avoid wiring the product'