PDF《Dimensioned drawing》

Leuze electronic GmbH + Co.

KG In der Braike

1 D-73277 Owen Tel. +49 (0)

7021 573-0 [email protected] ? www.leuze.com We reserve the right to make changes ? DS_LPS36HI_en_50118357_03.fm ? Light section sensor for object measure- ment ? Calibrated system ? Measurement range x-axis:

46 … 140mm ? Measurement range z-axis:

200 … 600mm ? Measurement time: 10ms ? Measurement data transfer via Fast Ethernet ? Measurement value display in mm on OLED display as an alignment aid ? Incremental transmitter input ? Up to

240 value pairs (x,z) along the laser line ? Up to

16 inspection tasks ? Activation input, trigger input, operational readiness output, cascading output

200 … 600mm Accessories: (available separately) ? Mounting systems BT 56, BT

59 ? Cable with M12 connector (K-D …) ? Configuration memory K-DS M12A-8P-0,75m-LxS36-CP IEC 60947... IEC 60947... IP

67 Dimensioned drawing A Transmitter B Receiver C Optical axis D X1: M12x1 connector, 8-pin, A coded E X2: M12x1 socket, 4-pin, D coded F X3: M12x1 socket, 8-pin, A coded (LPS 36/EN only) G X4: not used (dummy plug) H PE screw J OLED display and key pad K M4 thread, 4.5 deep L Holder for mounting system BT

56 / BT

59 M Zero point and orientation of the coordinate system for measurement data N 4mm bore hole in transmitter axis -X +X +Z Measurement range, typical +z -x -25 +x +25 +75

100 0 +100 -75 +50 -50 -100

200 300

400 500

600 Leuze electronic Measurement range z-axis x = measurement range x-axis Dimensions in mm LPS

36 HI Light section sensor for object measurement LPS 36HI… -

04 en 04-2014/06 50118357-03 LPS 36HI… -

04 2014/06 Specifications Interface assignments Optical data Measurement range 1) x-axis z-axis 1) Luminosity coefficient 6% ... 90%

46 … 140mm

200 … 600mm Light source laser Wavelength 658nm (visible red light) Max. output power <

8mW Pulse duration <

3ms Exposure time

60 … 1300μs Laser line approx. 170x1.5mm at 600mm Error limits (relative to measurement distance) Geometric resolution 2) x-axis z-axis 2) Minimum and maximum value dependent on the measurement distance, at 20°C after 30min. warmup time, average range UB, z resolution at factory setting median

3 0.2 … 0.6mm 0.1 … 0.9mm Linearity z-axis 3) 3) Reflectivity 90%, identical object, identical environment conditions, measurement object ≥ 20mmx20mm ≤ ±0.5% Repeatability z-axis 3) ≤ ±0.25% B/w detect. thresholds (6 … 90% rem.) ≤ ±0.5% Timing Measurement time 10ms Delay before start-up approx. 1.5s Electrical data Operating voltage UB 4) 4) For UL applications: for use in class

2 circuits according to NEC only

18 … 30VDC (incl. residual ripple) Residual ripple ≤ 15% of UB Open-circuit current ≤ 200mA Ethernet interface UDP Switching outputs

1 (ready) / 100mA / push-pull 5) on X1

1 (cascading) / 100mA / push-pull 5) on X1 5) The push-pull switching outputs must not be connected in parallel Inputs

1 (trigger) on X1

1 (activation) on X1 Signal voltage high/low ≥ (UB-2V)/≤ 2V Indicators Green LED continuous light ready off no voltage Yellow LED continuous light Ethernet connection available flashing Ethernet data transmission active off no Ethernet connection available Mechanical data Housing aluminum frame with plastic cover Optics cover glass Weight 620g Connection type M12 connector Environmental data Ambient temp. (operation/storage) -30°C … +50°C/-30°C … +70°C Protective circuit 6) 6) 1=transient protection, 2=polarity reversal protection, 3=short circuit protection for all outputs 1, 2,