PDF《2010-09-24》

0002 #35 H1023 O R CH1 max. weight #36 H1024 O R CH2 max. weight Set up the max. weight. When the measured value exceeds the set value, error codes will be recorded. #37 H1025 O R/W Upper limit for CH1 zero point check #38 H1026 O R/W Upper limit for CH2 zero point check Reference for reset to zero. When the weight is within this range, the status code will be set to zero bit , indicating the current zero weight status. Default: K10 Range: K-32,768 to K32,767 #39 H1027 O R/W Lower limit for CH1 zero point check #40 H1028 O R/W Lower limit for CH2 zero point check Reference for reset to zero. When the weight is within this range, the status code will be set to zero bit , indicating the current zero weight status. Default: K-10 Range: K-32,768 to K32,767 #41 H1029 X R/W Saving set value (H'

5678) Save the present set value and write all the set values into the internal Flash for use next time DVP02LC-SL is switched on. H0: No action, Default H'

FFFF: Saving is successful H'

5678: Write to internal Flash When H'

5678 is written in, all set values will be saved in Flash. When the saving is completed, CR#41 will become H'

FFFF. If the value written in is not H'

5678, it will automatically return to H0, e.g. write K1 into CR# to return to K0. -

5 - CR# Add. Attrib. Register name Explanation #43 H102B X R/W CH1 filter percentage #44 H102C X R/W CH2 filter percentage Default: K2 Range: K1 to K5 (Unit: 10%) #45 H102D X R/W CH1 filter average value #46 H102E X R/W CH2 filter average value Display average weight after filtering. Condition to enable filter: average time ≥

30 #50 H1032 X R Status code b0 (H'

0001): CH1 zero weight (empty) b1 (H'

0002): CH2 zero weight (empty) b2 (H'

0004): CH1 exceeds max. weight (overload) b3 (H'

0008): CH2 exceeds max. weight (overload) b4 (H'

0010): CH1 stable measured value b5 (H'

0020): CH2 stable measured value b6 ~ b15: Reserved #51 H1033 X R Error code Store all the error statuses. See Error Code Table below. Default: H'

0000 #52 H1034 O R/W RS-232 node address #53 H1035 O R/W RS-232 communication setting #54 H1036 O R/W RS-485 node address #55 H1037 O R/W RS-485 communication setting For CR#52, CR#54 default =

1 Range: K1 to K255 For CR#53, CR#55 default = H'

0000;

Range: ASCII, 9600, 7, E, 1. See Communication Format Table below. Symbols: O means latched. X means not latched. R means can read data. W means can write data. c Error Code Table for CR#51: bit Content Error bit Content Error b0 K1 (H'

0001) Power supply abnormality b1 K2 (H'

0002) Hardware abnormality b2 K4 (H'

0004) CH1 conversion error b3 K8 (H'

0008) CH1 SEN voltage error b4 K16 (H'

0010) CH2 conversion error b5 K32 (H'

0020) CH2 SEN voltage error b6 ~ b15 K64 (H'

0040) Reserved Note: Every error status is decided by its corresponding bit, so there might be more than

2 error statuses occurring at the same time.

0 refers to no error;

1 refers to error occurring. c Communication Format Table for CR#53, CR#55: bit15 bit14~bit8 bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0 ACSII/RTU Reserved Baudrate Data length Stop bit Parity Description bit15 ACSII/RTU

0 ASCII

1 RTU

0 9,600 bps

1 19,200 bps

2 38,400 bps

3 57,600 bps bit7~bit4 Baudrate

4 115,200 bps

5 Else none bit3 Data length (RTU =

8 bits)

0 7

1 8 bit2 Stop bit

0 1 bit

1 2 bits

0 Even

1 Odd bit1~bit0 Parity

2 None

3 None -

6 - 繁体中文 感谢您采用台达 DVP 系?产品.台达再?推出 Load Cell 秤重?测模组 DVP02LC-SL. DVP02LC-SL 提供