PDF《注意事项》

Warning Read this instruction sheet carefully before using DVPAEXT01-H.

DVPAEXT01-H is an OPEN TYPE device and therefore should be installed in an enclosure free of airborne dust, humidity, electric shock and vibration. The enclosure should prevent non-maintenance staff from operating the device (e.g. key or specific tools are required to open the enclosure) in case danger and damage on the device may occur. DVPAEXT01-H (including DVPAEXT1L-H and DVPAEXT1R-H) is used for connecting MPU and extension unit or among extension units. Use DVPACAB4A09/DVPACAB4A18 to extend the transmission distance between DVPAEXT1L-H and DVPAEXT1R-H. Make sure the power of the MPU and extension unit is switched off when wiring and power on MPU and the extension unit after the installation of DVPAEXT01-H is completed. Introduction Thank you for choosing Delta's DVP series accessory. DVPAEXT01-H is a connector for the extension cable of extension units. The maximum extension distance available is 1.8m. DVPAEXT01-H is only applicable for the connection between DVP-EH/EH2/PM series MPU and DI/DO, AI/AO extension units and does not occupy any extension point or module space. Product Profile & Outline DVPAEXT1L-H in the left side (prior level) DVPAEXT1R-H in the right side (next level)

1 3

4 3

5 5

2 6

6 1

3 4

6 6

3 3 Unit: mm

1 Upper cover of connection port

4 DIN rail

2 Terminal for extension cable

5 Extension cable

3 DIN rail clip

6 Direct fixing hole ENGLISH Specifications DVPAEXT01-H Model Item DVPAEXT1L-H DVPAEXT1R-H Power supply Supplied by MPU through its internal bus: 5V DC (4.5 VDC ~ 5.5 VDC) (-10% ~ 10%) Power consumption 0.5W 0.5W Noise immunity ESD: 8KV Air Discharge EFT: Power Line: 2KV RS: 26MHz ~ 1GHz, 10V/m Operation/storage Operation: 0° C ~ 55° C (temperature),

50 ~ 95% (humidity), pollution degree

2 Storage: -25° C ~ 70° C (temperature),

5 ~ 95% (humidity) Shock/vibration immunity International standard: IEC61131-2, IEC 68-2-6 (TEST Fc)/IEC61131-2 & IEC 68-2-27 (TEST Ea) Weigh (g)

100 100 Installation and Wiring Connect DVPAEXT01-H with modules Using DVPAEXT01-H to connect DVP-EH/EH2/PM series MPU with DI/DI, AI/AO extension units. Cable Connection When installing DVPAEXT1L-H and DVPAEXT1R-H, please use DVPACAB4A09/DVPACAB4A18 connection cable.

25 14

13 1

1 13

14 25 TO DVPAEXT1L-H

25 PIN D-SUB TO DVPAEXT1R-H

25 PIN D-SUB

25 PIN D-SUB female DVPAEXT1L-H COM Port

25 1

1 25

25 PIN D-SUB female DVPAEXT1R-H COM Port . . . Note: The DVPAEXT01-H package does not contain the connection cables mentioned above. Please purchase the cables from our distributors. 注意事项 请在使用之前,详细阅读本使用说明书. 本机为开放型(OPEN TYPE)机壳,因此使用者使用本机时,必须将之安装於具防尘、防潮及免於电击/ 冲击意外之外壳配线箱内.另必须具备保护措施(如:特殊之工具或钥匙才可打开)防止非维护人员操作 或意外冲击本体,造成危险及损坏. 本产品DVPAEXT01-H(内含DVPAEXT1L-H 与DVPAEXT1R-H)用於主机与扩充机之间或扩充机与扩充 机连接延长之用.DVPAEXT1L-H 与DVPAEXT1R-H 之间可以连接线(DVPACAB4A09/DVPACAB4A18) 来延长传输距离. 配线时请务必关闭主机与扩充机电源,安装完成后,才可上电. 产品简介 谢谢您采用台达 DVP 配件.本机为扩充机延长线连接器,有效延伸距离最大为 1.8 公尺.仅适用於 DVP-EH/EH2/PM 系列主机与DI/DO、AI/AO 扩充机间之连线,且不占用扩充点点数及扩充模组台数. 产品外观及各部介绍 DVPAEXT1L-H 为左侧(前级) DVPAEXT1R-H 为右侧(后级)