PDF《TEST REPORT》

EPA 6010C-2007, analysis was performed by ICP-OES. Test Item Unit MDL Test Result 1# Sb mg/kg

10 N.D. 4. 8P Test Method: With reference to CPSC-CH-C1001-09.3, analysis was performed by GC-MS. Remark: ***The Limited value is based on the standard set forth in the U.S. Consumer Product Safety Improvement Act Section

108 Test Items Unit MDL Test Results Limited Value*** Note 2# Dibutyl phthalate (DBP) % 0.005 N.D. 0.1 For all toys and childcare articles Butylbenzyl phthalate (BBP) 0.005 N.D. 0.1 Di-(2-ethylhexyl)-phthalate (DEHP) 0.005 N.D. 0.1 Di-n-octyl phthalate (DNOP) 0.005 N.D. 0.1 For toys and childcare articles that can be mouthed Di-iso-nonyl phthalate (DINP) 0.005 N.D. 0.1 Di-iso-decyl phthalate (DIDP) 0.005 N.D. 0.1 Diisobutyl phthalate(DIBP) 0.005 N.D. Di-n-hexyl phthalate(DNHP) 0.005 N.D. TEST REPORT No. : SH151000187C01 Report Date: 2015/10/27 Page

4 of

8 www.uts.com.cn 5. HBCDD Test Method: With reference to EPA 3550C-2007&

EPA 8270D-2007, analysis was performed by GC-MS. Note : 1)Not Regulated. 2) MDL = Method Detection Limit. 3) N.D. = Not detected, less than MDL. 4) M1: With reference to IEC 62321-5: 2013, analysis was performed by ICP-OES. 5) M2: With reference to IEC 62321-4: 2013, analysis was performed by ICP-OES. 6) M3: With reference to IEC 62321: 2008, analysis was performed by UV-Vis. M3a:With reference to IEC 62321: 2008, analysis was performed by Spot test/UV-Vis Colorimetric Determination. 7) M4: With reference to IEC 62321: 2008, analysis was performed by GC-MS. 8) Spot test: Negative=Not detected Cr(VI) in plating;

Positive=Detected Cr(VI) in plating. (If you are not sure about the result of the Spot test, use the boiling water extraction method to confirm the result) Boiling water extraction method: Negative= Not detected Cr(VI) in plating;

Positive=The Cr(VI) concentration detected is equal to or greater than 0.02mg/kg with a sample surface area of 50cm2 used. TEST PART DESCRIPTION: 1# Metallic pin 2# Black main body Test Item Unit MDL Test Result 2# Hexabromocyclododecane (HBCDD) mg/kg

20 N.D. TEST REPORT No. : SH151000187C01 Report Date: 2015/10/27 Page

5 of

8 www.uts.com.cn FLOW CHART 1. Test for Pb, Hg, Cd and Sb Content Add suitable digestion acid in the digestion vessel. Transfer the digestive solution into a suitable volumetric flask. Analyze by ICP-OES. Weigh sample and place in a digestion vessel. Digest sample completely in microwave digestion oven. Make up with deionized water. 2. Test for Chromium(Ⅵ)Content Nonmetal Weigh sample in a flat-bottomed bottle. Add appropriate amount of digestion reagent and heating. Cool, filter then adjust the pH of the filtrate to 7.5±0.5. Add diphenyl-carbazide, and make up to the mark. Adjust the pH of the solution to 2.0±0.5. Measure the absorbance at 540nm by UV-Vis. Sample Material Digestion Acid Glass HNO3/HF Plastic H2SO4, H2O2, HNO3, HCl Others Any acid to total digestion. TEST REPORT No. : SH151000187C01 Report Date: 2015/10/27 Page

6 of

8 www.uts.com.cn Metal Pre-treatment of Sample: Clean the surface;

if there is oil layer or polymer coating on the surface, remove it. Configuration of test liquid. Dip one to five drops of test liquid to the surface. If there is hexavalent chromium, violet color will appear within several minutes. If the color appears after a long time, it will not be considered. If the test result is positive, it can be considered that there is hexavalent chromium. If the test result is negative. Wipe the surface of the coating lightly with fine sandpaper and dip test liquid. If the test result is positive, it can be considered that hexavalent chromium coating exists. If the test result is still negative. Wipe the coating more deeply and continue the test until it reaches the surface. If the test result is still negative, it can be considered that sample is below the detection limit. If you are not sure about the result of the point measurement, use the followin........