PDF《DOP-B10》

DOP-B10 High Color?Wide Screen? User-Friendly HMI Products No.

18, Xinglong Rd., Taoyuan City 33068, Taiwan Instrunction Sheet (1) Preface Thank you for purchasing DELTA'

s DOP-B series. This instruction sheet will be helpful in the installation, wiring and inspection of Delta HMI. Before using the product, please read this instruction sheet to ensure correct use. You should thoroughly understand all safety precautions before proceeding with the installation, wiring and operation. Place this instruction sheet in a safe location for future reference. Please observe the following precautions: ? Install the product in a clean and dry location free from corrosive and inflammable gases or liquids. ? Ensure that all wiring instructions and recommendations are followed. ? Ensure that HMI is correctly connected to a ground. The grounding method must comply with the electrical standard of the country (Please refer to NFPA 70: National Electrical Code,

2005 Ed.). ? Do not disassemble HMI, modify or remove wiring when power is applied to HMI. ? Do not touch the power supply during operation. Otherwise, it may cause electric shock. If you have any questions during operation, please contact our local distributors or Delta sales representatives. The content of this instruction sheet may be revised without prior notice. Please consult our distributors or download the most updated version at http://www.delta.com.tw/ia. (2) Pin Definition of Serial Communication DOP-B10S411 / DOP-B10S511/ DOP-B10E515 COM1 Port COM Port PIN MODE1 RS-232

1 2 RXD

3 TXD

4 5 GND

6 7 RTS

8 CTS

9 Note1: Blank = To avoid malfunction, it must be left unconnected. DOP-B10S411 / DOP-B10S511 COM2 Port COM Port PIN MODE1 MODE2 MODE3 COM2 COM3 COM2 COM3 COM2 COM3 RS-232 RS-232 RS-485 RS-485 - RS-422

1 D+ TXD+

2 RXD

3 TXD

4 D+ RXD+

5 GND GND GND

6 D- TXD-

7 TXD

8 RXD

9 D- RXD- Note1: Note1: Blank = To avoid malfunction, it must be left unconnected. Note2: DOP-B10S411 / DOP-B10S511 models do not support RS-422 flow control. DOP-B10E515 COM2 Port COM Port PIN MODE1 MODE2 MODE3 RS-232 RS-422 RS-485

1 TXD+ D+

2 RXD

3 TXD

4 RXD+

5 GND GND GND

6 TXD- D-

7 RTS

8 CTS

9 RXD- Note1: Note1: Blank = To avoid malfunction, it must be left unconnected. Note2: When COM2 port is used for RS-232 flow control (RTS, CTS is set), COM3 port cannot be used. Note3: When COM2 port is used for RS-422 flow control, for the pin settings it needs, please refer to the pin definitions of MODE

2 in DOP-B10E515 COM3 port table. DOP-B10E515 COM3 Port COM Port PIN MODE1 MODE2 MODE3 RS-232 RS-422 RS-485

1 TXD+(RTS+) D+

2 RXD

3 TXD

4 RXD+(CTS+)

5 GND GND GND

6 TXD-(RTS-) D-

7 8

9 RXD-(CTS-) Note1: Note1: Blank = To avoid malfunction, it must be left unconnected. Note2: When COM2 port is used for RS-422 flow control, for the pin settings it needs, please refer to the pin definitions of MODE

2 in DOP-B10E515 COM3 port table. (3) Parts Names DOP-B10S411 (Front View) A Power LED Indicator ( ) Note: Lights in green when HMI works normally. B Touch Screen / Display DOP-B10S411 (Rear View) A Power Input Terminal D USB Slave B COM2 E USB Host C COM1 Please note DOP-B10S411 model has not system key, user could press at blank space for

3 seconds, and then will hear Buzzer sound. After hearing the Buzzer sounded, please press left top corner to enter system menu. DOP-B10S511 / DOP-B10E515 (Front View) A Power LED Indicator ( ) Lights in green when HMI works normally. B Operation LED Indicator ( ) /Alarm LED Indicator ( ) Lights in blue: the communication is carried out / the data is accessing. (Please refer to the Note below for explanation). Lights in red: one of the alarms is on. C Touch Screen / Display Note: The definition of the operation LED indicator (Blue) can be determined by the users freely. Please note that DOP-B10S511 model only has Power LED Indicator (A) and Touch Screen / Display (C). A B C E PIN1 PIN1 A A B PIN1 PIN1 D B C DOP-B10S511 / DOP-B10E515 (Rear View) A Power Input Terminal F USB Slave B COM2 (It is provided with two LED indicators to indicate that HMI is in Read or Write status during the communication process.) G Ethernet Interface (LAN) Note: DOP-B10E515 only. C COM3 (It is provided with two LED indicators to indicate that HMI is in Read or Write status during the communication process.) Note: DOP-B10E515 only. H Audio Output Interface Note: DOP-B10E515 only. D COM1 I Memory Card Slot Note: DOP-B10E515 only. E USB Host Please note DOP-B10S511 / DOP-B10E515 model has not system key, user could press at blank space for