PDF《DOP-107EV》

DOP-107EV DOP-107CV High color?Wide screen?User-friendly Delta Electronics, Inc.

No.18, Xinglong Rd., Taoyuan City 33068, Taiwan Instruction Sheet (1) General precautions Thank you for purchasing this product. This instruction sheet provides information about the DOP-100 series HMI. Before using this product, please read through this instruction sheet carefully to ensure the correct use of the product. Please keep this sheet handy for quick reference whenever needed. Before finishing reading this sheet, please follow the instructions below: ? Install the product in an indoor location, which is free of vapor, corrosive and inflammable gas and liquids. ? Please refer to the wiring diagram when connecting the wires. ? Ensure your HMI is correctly grounded. The grounding method must comply with the national electrical standard (please refer to NFPA 70: National Electrical Code,

2005 Ed.). ? Do not disassemble the HMI or change the wiring when power is on. ? Do not touch the power supply when power is on, or it may cause electric shock. ? When the HMI displays a low power notification and requires a battery change, please contact your local distributor or Delta Customer Service Center for the replacement. Do not change the batteries by yourself. ? This product can be used with other industrial automation equipment. Please read through this sheet carefully and install the product according to the instructions to avoid danger. ? Cleaning method: please use a dry cloth to clean the product. ? This product must be used at an altitude below 2,000 m. ? If the equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be impaired. ? For repair and maintenance, please contact Delta Electronics, Inc. Address: No.18, Xinglong Rd., Taoyuan City, Taiwan. TEL: +886-3-3626301. If you have any inquiry during operation, please contact our local distributors or Delta sales representatives. The content of this instruction sheet may be revised without prior notice. Please consult our distributors or download the latest version at Delta'

s website (http://www.delta.com.tw/ia). (2) Communication port pin assignment DOP-107CV / DOP-107EV COM1 COM Port Pin MODE1 RS-232

1 -

2 RXD

3 TXD

4 -

5 GND

6 -

7 RTS

8 CTS

9 - DOP-107CV / DOP-107EV COM2 COM Port Pin MODE1 MODE2 MODE3 COM2 COM3 COM2 COM3 COM2 COM3 RS-232 RS-485 RS-485 RS-485 RS-232 RS-422

1 - - D+ - - TXD+

2 RXD - - - RXD -

3 TXD - - - TXD -

4 - D+ - D+ - RXD+

5 GND GND GND

6 - - D- - - TXD-

7 RTS - - - RTS -

8 CTS - - - CTS -

9 - D- - D- - RXD- Note: mark - means connection is not required. (3) Description of each part DOP-107CV / DOP-107EV (front view) A Operation / display area DOP-107CV / DOP-107EV (rear view) A Power input terminal (24AWG wire min.) B COM2/COM3 C COM1 D USB Host E Network port (LAN) Only for DOP-107EV F USB Slave (4) Mounting dimensions DOP-107CV / DOP-107EV Unit: mm (inch) Operation temperature: 0°C to 50°C (32°F to 122°F) Storage temperature: -20°C to 60°C (-4°F to 140°F) (5) Installation and wiring Precautions: ? Incorrect installation may result in malfunction. ? To ensure the HMI is well ventilated, make sure there is sufficient space between the HMI and the adjacent objects or walls. ? This product should be used on a case / platform which conforms to enclosure Type 4X standard (for indoor use only). ? The maximum panel thickness for mounting must be no greater than

5 mm. Installation steps: Step 1: Put the waterproof gasket into the HMI and then insert the HMI into the panel cutout. Step 2: Place the fasteners into the slots and tighten the screws until reaching the panel cutouts. Step 3: Tighten the screws with the torque less than 0.5 N-M / 0.7 N-M to avoid damage to the plastic case. Torque for DOP-107CV / DOP-107EV: 6.17 lb-inch (0.7 N-M) Step 4: For heat dissipation, please keep a minimum clearance of