PDF《产品规格书》

2 PAGE:

4 /

8 5.参数范围 Parameter Ratings: 6.产品性能 Performance 6.1 机械性能 Mechanical 序号 No. 项目Item 测试条件 Test Condition 规格Requirement 6.1.1 外观 Appearance 目测 Checking by eye 视力:1.0 以上 Eyesight: > 1.0 照明: (200~300)lx Lamp: (200~300)lx 目测距离: (0.3~0.5)m Space: (0.3~0.5)m GB/T 5095.1 Method 1a 1.塑料件表面应无明显疤痕、凹陷、开裂及影响使用的变形. Plastic part: smooth and flat surface without discolor, broken, crack, and distortion, etc.

2 金属件表面无锈蚀、氧化 、无明显的机械损伤及电镀层脱 落等缺陷. Metal part: bright and even surface without rust, oxide, fog and obvious physical damage, etc. 6.1.2 端子的插入力 与固定力 Insertion force and Retention Force for Contact 固定连接器和/或测力计,在连接器轴线方向插入和拔出;

速度不大于

25 mm/min. Axial Insert and withdraw force on the contact in the housing at a rate less than

25 mm/min. GB/T 5095.8 Method 15d / EIA-364-29B 插入力 (Insertion) Max. 固定力(Retention) Min. 10N 15N 6.1.3 针的固定力 Retention Force for Pin 固定连接器/或测力计,在连接器轴线方向施加规定的推 力进行测试, 速度不大于 25mm/min. Apply thrust force on the pin in the wafer at a rate of

25 mm/min . GB/T 5095.8 Method 15a / EIA-364-29B 8N Min 6.1.4 压着部位抗张 强度 Crimping Pull Out Force 在试验装置夹头中固定试验样品, 在连接的轴线方向施加 张力;

速度不大于 25mm/min. Fix the crimped contact, Axial pull out force on the contact in the housing at a rate less than

25 mm/min. GB/T5095.8 Method 16d / EIA-364-08B AWG 28: 10N Min. AWG 26: 20N Min. AWG 24: 30N Min. AWG 22: 40N Min. 额定电流 Rated Current 3A 适用 PCB 板Applicable P.C.B Board Thickness: 1.6mm Hole Diameter: 1.02mm~1.12 mm 额定电压 Rated Voltage 250V [AC(有效值 rms)/DC] 使用温度范围 Operating temperature range -40℃~+105℃ 适用线型 Applicable wires Wire Size:AWG22~AWG28(0.32mm?-0.08 mm?) Insulation Diameter:1.6mm-1.2mm 产品规格书 PRODUCT SPECIFICATION 产品名称 Product Name: TJC8 编号 Document No. PS3879 版本号 VersionNo.

2 PAGE:

5 /

8 6.1.5 成品插入力与 拔出力 Insertion and Withdrawal Force for Connector 固定连接器和/或测力计,在连接器轴线方向插入和拔出;

速度不大于25mm/min. Apply Axial Insert and withdraw force on the contact in the housing at a rate less than

25 mm/min. GB/T 5095.7 Method 13b / EIA-364-13B 插入力(最大值) Insertion(Max.) 拔出力(最小值) Withdrawal(Min) 13N Max. per Pin 0.7N Min per Pin 6.1.6 机械振动 Random Vibration 插合连接器,串联在一直流电源上,电流100mA;

并模拟正 常工作状态;

振频为(10~55~10)Hz,每个循环时 间为1分钟,振幅1.52mm.沿XYZ三轴正反方向各循环 2h. Mated connectors subjected to following vibration conditions, for a period of

2 hours in each of

3 mutually perpendicular axes,

100 mA current shall be applied. Frequency: (10~55~10)HZ/min. Amplitude: 1.52mm GB/T 5095.4 Method 6d / EIA-364-28D 外观:无损伤(参照6.1.1) Appearance: No damage.( refer to 6.1.1) 接触电阻:0.04Ω Max. Contact resistance: 0.04Ω Max. 中断: 1μsec Max.