PDF《Installation Instructions》

Mounting Kits For Wide Panel Antennas ? DB380 and DB380-3 Pipe Mounts DB5083 and DB5083D Downtilt Mounts Page

1 of

4 Installation Instructions Bulletin 095351-000 ? Revision AE ? July

2013 CommScope Infrastructure Academy offers installation training.

3 PARTS LIST

3 M10-1.5 X

35 Hex HD Bolt, HTSTL,GALV

4 6

58 N.m (43ft Ibs) M12

37 N.m (27ft Ibs) M10 MAXIMUM TORQUE VALUES

4 M10 Split Lock Washer, STL,GALV

4 6

5 M10-1.5 Hex HD Nut, STL,GALV

8 12

6 M12-1.75 X

190 Hex HD Bolt, STL,GALV

4 6

7 M12 Flat Washer, STL,GALV

8 12

8 M12 Split Lock Washer, STL,GALV

4 6

9 M12-1.75 Hex HD Nut, STL,GALV

8 12 Item Description Qty DB380 DB380-3

1 Bracket With Tabs

2 3

2 Bracket Without Tabs

2 Item Description Qty DB5083 DB5083D

1 Downtilt Bracket

1 2

2 Downtilt Bracket

1 2

3 M10 Split Lock Washer, STL,GALV

4 8

4 M10-1.5 Hex HD Nut, STL,GALV

8 16

5 M10-1.5 X

35 Hex HD Bolt, HTSTL, GALV

4 8

6 M10 Tooth Lock Washer, STL,GALV

2 4 DB380/DB380-3 GENERAL INFORMATION with no significant side wind load. ? Position the antenna with its up arrow label pointing upward before installation. This orientation allows the drain holes to be on the bottom of the (continued on page 2) antenna. mount). has

2 mounting brackets (uses DB5083 for downtilt ? DB380 has

2 clamp assemblies. Each clamp assembly angle members up to 2.5 (63.5 mm) on a side. PRE-INSTALLATION INSTRUCTIONS

60 to

115 mm) OD or ? Fits round members 2.4 to 4.5 ( mount). has

3 mounting brackets (uses DB5083D for downtilt ? DB380-3 has

3 clamp assemblies. Each clamp assembly ? Examine antenna and hardware to ensure that all parts are enclosed and that there is no physical damage. ? Check to ensure that the antenna feed connector mates with the jumper cable. ? Verify that the frequency range shown on the label on the back of the antenna matches the frequency range of the station equipment. Note: Minimum pipe diameter recommended is

60 mm (2.4 ). These mounts can be used on pipe diameters measuring down to

33 mm (1.3 );

this is only recommended for building mounts or however, applications DB5083/DB5083D results of improper or unsafe installation practices. * is in the area.Do not use metal day or when lightning or thunder Do not install on a wet or windy rubber gloves. including a long-sleeved shirt and heels. Wear protective clothing Wear shoes with rubber soles and Do not install near power lines. electrocute you. Assume any wire or line can and guy wires look the same. Power lines, telephone lines, ladder. NOTICE The installation, maintenance, or removal of an antenna requires qualified, experienced personnel. Andrew installation instructions are written for such installation personnel. Antenna systems should be inspected once a year by qualified personnel to verify proper installation, maintenance, and condition of equipment. Andrew disclaims any liability or responsibility for the * included with DB380-3 Middle pipe bracket is truly vertical. DB380/DB380-3 and DB5083/DB5083D Mounting Kits Bulletin 095351-000 ? Revision AE ? July

2013 ? Page

2 of

4 (Continued from page 1) DB380/DB380-3 Pipe Mount Clamp. Use inclinometer to verify antenna Attaching Antenna to a Mast Using DB380/DB380-3 Pipe Mount. Bracket Without Tab M12 Flat Washer M12C1.75 X

190 Hex HD Bolt M10 Split Lock Washer M10C1.5 Hex HD Nut Hex HD Bolt M12C1.75 X

190 With Tabs Bracket Without Tabs Bracket Hex HD Nut M12 Split Lock Washer M12 Flat Washer Antenna Bracket M10C1.5 Hex HD Nut M12C1.75 Lock Washer M10 Split Hex HD Nut M12C1.75 Lock Washer M12 Split Washer M12 Flat Hex HD Bolt M10C1.5 X