PDF《PLG》

60 CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS PLG Radial Lead Type, Higher Capacitance Specifications Temperature Characteristics (Max.

Impedance Ratio) Category Temperature Range Rated Voltage Range Rated Capacitance Range Capacitance Tolerance Tangent of loss angle (tan δ) ESR ( 1) Leakage Current ( 2) Performance Characteristics Item C55 to +105°C 2.5 to 16V

330 to 3900?F ±20% at 120Hz, 20°C Less than or equal to the specified value at 120Hz, 20°C Less than or equal to the specified value at 100kHz, 20°C Less than or equal to the specified value. After

2 minutes' application of rated voltage at 20°C Z+105°C / Z+20°C 1.25 (100kHz) ZC55°C / Z+20°C 1.25 Endurance Damp Heat (Steady State) Resistance to Soldering Heat Marking The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for

2000 hours at 105°C. The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for

1000 hours at 60°C, 90% RH. After soldering the capacitor under the soldering conditions prescribed here as preheat at

150 to 200°C for

60 to

180 seconds and peak temperature at 265°C for

10 seconds or less, the capacitor shall meet the specifications listed at right, provided that its temperature profile is measured at both of terminal ends facing the soldering side. Navy blue print on the case top Capacitance change tan δ Leakage current ( 2) ESR ( 1) Within ± 20% of the initial capacitance value ( 3) 150% or less than the initial specified value 150% or less than the initial specified value Less than or equal to the initial specified value Capacitance change tan δ Leakage current ( 2) ESR ( 1) Within ± 20% of the initial capacitance value ( 3) 150% or less than the initial specified value 150% or less than the initial specified value Less than or equal to the initial specified value Capacitance change tan δ Leakage current ( 2) ESR ( 1) Within ± 10% of the initial capacitance value ( 3) 130% or less than the initial specified value 130% or less than the initial specified value Less than or equal to the initial specified value Higher Capacitance, Low ESR, High ripple current. Load life of

2000 hours at 105°C. Radial lead type : Lead free flow soldering condition correspondence Compliant to the RoHS directive (2011/65/EU).

1 ESR should be measured at both of the terminal ends closest to the capacitor body.

2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for

120 minutes at 105°C.

3 Initial value : The value before test of examination of resistance to soldering. P

1 L

2 G

3 0

4 G

5 1

6 2

7 2

8 M

9 C

10 O

11 1

12 Configuration Size code Capacitance tolerance (±20%) Rated capacitance (1200?F) Rated voltage (4V) Series name Type L+0.5MAX. 15MIN 4MIN φ D±0.5 Resin coated Case φd L G

1 2

0 0 g

8 4

1 Capacitance Series Lot. No. Voltage(g:4V) P ±0.5 Dimensions Type numbering system (Example : 4V 1200?F) Size φD L P φd φ8 * 9L 8.0 8.5 3.5 0.6 φ8 * 12L 8.0 11.5 3.5 0.6 φ10 * 13L 10.0 12.5 5.0 0.6 (mm) Dimension table in next page. PLG PLF Higher Capacitance Voltage V 2.5

4 6.3

10

16 Code e g j A C Please refer to page

20 about the end seal configuration. Frequency coefficient of rated ripple current

0 Frequency0/ Coefficient 120Hz 1kHz? 10kHz 100kHz or more 0.05 0.30 0.70 1.00