PDF《产品规格书》

1.0 照明: (200~300)lx Lamp: (200~300)lx 目测距离: (0.3~0.5)m Space: (0.3~0.5)m GB/T 5095.1 Method 1a 1.塑料件表面应无明显疤痕、凹陷、开裂及影响使用的变形. Plastic part: smooth and flat surface without discolor, broken, crack, and distortion, etc.

2 金属件表面无锈蚀、氧化 、无明显的机械损伤及电镀层脱 落等缺陷. Metal part: bright and even surface without rust, oxide, fog and obvious physical damage, etc. 6.1.2 端子的插入力 与固定力 Insertion force and Retention Force for Contact 固定连接器和测力计,在连接器轴线方向插入和拔出;

速 度不大于

25 mm/min. Axial Insert and withdraw force on the contact in the housing at a rate less than

25 mm/min. GB/T 5095.8 Method 15d / EIA-364-29B 插入力 (Insertion) Max. 固定力(Retention) Min. 9.8N 20N 6.1.3 压着部位抗张 强度 Crimping Pull Out Force 在试验装置夹头中固定试验样品, 在连接的轴线方向施加 张力;

25 mm/min. Fix the crimped contact, axial pull out force on the contact in the housing at a rate less than

25 mm/min. GB/T5095.8 Method 16d / EIA-364-08B AWG 28: 10N Min AWG 26: 20N Min. AWG 24: 30N Min. AWG 22: 40N Min. 额定电流 Rated Current 3A [AC(有效值 rms)/DC] 额定电压 Rated Voltage 250V [AC(有效值 rms)/DC] 使用温度范围(包含温升) Operating temperature range (Include temperature rise) -25℃~+85℃ 适用线型 Applicable wires Wire Size:AWG28~AWG22(0.08mm?-0.32mm?) Insulation Diameter:1.2mm-1.6mm 产品规格书 PRODUCT SPECIFICATION 产品名称 Product Name: TJC50014-2Y 编号 Document No. PS3802 版本号 VersionNo.

0 PAGE:

5 /

7 6.1.4 机械振动 Random Vibration 插合连接器,串联在一直流电源上,电流100mA;

并模拟正 常工作状态;

振频为(10~55~10)Hz,每个循环时 间为1分钟,振幅1.52mm.沿XYZ三轴正反方向各循环 2h. Mate connectors subjected them to following vibration conditions, for a period of

2 hours in each of

3 mutually perpendicular axes,

100 mA current shall be applied. Frequency: (10~55~10)HZ/min. Amplitude: 1.52mm GB/T 5095.4 Method 6d / EIA-364-28D 外观:无损伤(参照6.1.1) Appearance: No damage.( refer to 6.1.1) 接触电阻:0.02Ω Max. Contact resistance: 0.02Ω Max. 中断: 1μsec Max. 6.2 电气性能 Electrical 序号 No. 项目Item 测试条件 Test Condition 规格 Requirement 6.2.1 接触电阻 Contact Resistance 插配阴阳连接器后,用小功率电路进行测试 Mate connectors with dry circuit to test Contact Resistance GB/T 5095.2 Method 2a / EIA-364-23B 0.01 Ω Max. ( Initial) 0.02 Ω Max. (Final) 6.2.2 绝缘电阻 Insulation Resistance 在相邻接触件之间或地线之间,用500V DC 电压进行测 试. Apply a voltage of 500V DC between adjacent contacts and between contacts to ground. GB/T 5095.2 Method 3a / EIA-364-21C

1000 MΩ Min. ( Initial)

500 MΩ Min. (Final) 6.2.3 耐电压 Withstand Voltage 相邻接触件之间或地线之间施加 1000V AC (有效值),漏 电流 1mA 的电压作用,时间 1min. Apply a voltage of AC 1000V for

1 minute between adjacent contacts and between contacts to ground. GB/T 5095.2 Method 4a / EIA-364-20B 外观:无击穿和飞弧现象 Appearance: No Breakdown or flashover 6.2.4 温升 Temperature Rise 插合连接器,通以最大允许电流,测温度的差值 Mate connectors and measure the temperature rise of contact when the maximum AC rated current is passed. GB/T 5095.3 Method 5a / EIA-364-70A 30℃ Max. 6.3 环境性能 Environmental 序号 No. 项目Item 测试条件 Test Condition 规格Requirement 6.3.1 耐高温 Heat Resistance 连接器配合后, 于105±2℃的空气中放置