编辑: 5天午托 | 2019-09-14 |
1.16 产品名称 Product Name: SAN 中国・浙江省乐清市虹桥镇幸福东路
1098 号 合兴工业园 1098,Xingfu `Road(East),CWB Industrial Zone,Hongqiao,Yueqing,Zhejiang 325608,China Tel: 86-577-61313157 Fax: 86-577-62313682 审核 Check: 王曲 2019.1.16 编号 Document No.: PS3957 批准 Approval: 刘冬旭 2019.1.16 版本 REVISION:
2 PAGE:
1 /
7 产品描述:SAN Connector Product Description: SAN Connector 目录 Index 1. 更改履历 Change History 2. 范围 Scope 3. 产品描述 Product Description 4. 相关标准 Related Standards 5. 参数范围 Parameter Ratings 6. 产品性能 Performance 7. 测试分组 Test Sequences 产品规格书 PRODUCT SPECIFICATION 产品名称 Product Name: SAN 编号 Document No. PS3957 版本号 VersionNo.
2 PAGE:
2 /
7 1.更改履历 Change History 序号 No.: 版本号 Version No. 更改前描述 Description Before Modification 更改后描述 Description After Modification 日期 Date
1 1 PS0057/PS3095/PS1714/PS0450 PS3957(新版规格书整理) 吴吉 2017.5.20
2 2 / 更改 logo 张玲玲 2019.1.16
3 4
5 产品规格书 PRODUCT SPECIFICATION 产品名称 Product Name: SAN 编号 Document No. PS3957 版本号 VersionNo.
2 PAGE:
3 /
7 2.适用范围 Scope 本产品规格书适用于浙江合兴电子元件有限公司生产的 2.0mm 间距条形连接器,产品名称:SAN. This product specification covers the requirement for 2.0mm pitch Plug Housing, which is designed and manufactured by CWB Electronics(ZheJiang) Co.,LTD. P/N: SAN. 3.产品描述 Product Description SAN 系列产品为家电连接器产品,产品部件组成如下: The SAN seriers connector designed for home appliances connection. Part checklist as following form: 4.相关标准 Related Standards 以下参考文件是本规格书的一个组成部份.若本规格书中的要求与产品图纸发生冲突,则产品图中的要求为 优先;
若本规格书中的要求与参考文件中的要求冲突,则本规格书为优先. The following documents form a part of this specification. In the event of conflict between the requirements of this specification and the product drawing, the product drawing shall take precedence. In the event of conflict between the requirements of this specification and the referenced documents, this specification shall take precedence. GB/T
2421 电工电子产品环境试验 第一部分 总则 Testing Method for Environmental of Electrical Connectors Class 1: General Principles GB/T
2423 电工电子产品环境试验方法 Testing Method for Environmental of Electrical Connectors GB/T
2424 电工电子产品环境试验导则 Testing Method for Environmental of Electrical Connectors GB/T
5095 电子设备用机电元件基本试验规程及测量方法 Testing procedure/Method for components of electric equipment 产品符合合兴企标 Q/HX J1150001 《产品及所用材料的环保要求》 I 类或顾客要求. The connector should comply with CWB standard Q/HX J1150001 Class I or customer'
s requests Name Part name Notes 条形连接器针座 Plug Housing SAN-nA PA66 UL94-V0 PA66 UL94-V0 GWT 750℃ 插针 Pin Contact SAN-B/SAN-C/SAN-D Phosphor bronze , Tin Plating 产品规格书 PRODUCT SPECIFICATION 产品名称 Product Name: SAN 编号 Document No. PS3957 版本号 VersionNo.
2 PAGE:
4 /
7 5.参数范围 Parameter Ratings: 6.产品性能 Performance 6.1 机械性能 Mechanical 序号 No. 项目Item 测试条件 Test Condition 规格Requirement 6.1.1 外观 Appearance 目测 Checking by eye 视力:1.0 以上 Eyesight: >
1.0 照明: (200~300)lx Lamp: (200~300)lx 目测距离: (0.3~0.5)m Space: (0.3~0.5)m GB/T 5095.1 Method 1a 1.塑料件表面应无明显疤痕、凹陷、开裂及影响使用的变形. Plastic part: smooth and flat surface without discolor, broken, crack, and distortion, etc.
2 金属件表面无锈蚀、氧化 、无明显的机械损伤及电镀层脱 落等缺陷. Metal part: bright and even surface without rust, oxide, fog and obvious physical damage, etc. 6.1.2 端子固定力 Retention Force for Contact 固定连接器或测力计,在连接器轴线方向拔出;
速度不大 于25 mm/min. Axial withdraw force on the contact in the housing at a rate less than
25 mm/min. GB/T 5095.8 Method 15d / EIA-364-29B 固定力(Retention) Min. 10N 6.1.3 压着部位抗张 强度 Crimping Pull Out Force 在试验装置夹头中固定试验样品, 在连接的轴线方向施加 张力;
速度不大于 25mm/min. Fix the crimped contact, Axial pull out force on the contact in the housing at a rate less than
25 mm/min. GB/T5095.8 Method 16d / EIA-364-08B AWG 28: 10N Min. AWG 26: 20N Min. AWG 24: 30N Min. 6.2 电气性能 Electrical 序号 No. 项目Item 测试条件 Test Condition 规格 Requirement 6.2.1 绝缘电阻 Insulation Resistance 在相邻接触件之间或地线之间,用500V DC 电压进行测 试. Apply a voltage of 500V DC between adjacent contacts and between contacts to ground. GB/T 5095.2 Method 3a / EIA-364-21C
1000 MΩ Min. ( Initial)
500 MΩ Min. (Final) 额定电流 Rated Current 2A 适用 PCB 板Applicable P.C.B Board Thickness:1.2mm-1.6mm 额定电压 Rated Voltage 250V [AC(有效值 rms)/DC] 使用温度范围 Operating temperature range -25℃~+85℃ 适用线型 Applicable wires Wire Size: AWG28~AWG24 (0. 08097mm?-0. 2047mm?) Insulation Diameter:1.2mm-1.4mm 产品规格书 PRODUCT SPECIFICATION 产品名称 Product Name: SAN 编号 Document No. PS3957 版本号 VersionNo.
2 PAGE:
5 /
7 6.2.2 耐电压 Withstand Voltage 相邻接触件之间或地线之间施加 1000V AC (有效值),漏 电流 1mA 的电压作用,时间 1min. Apply a voltage of AC 1000V for
1 minute between adjacent contacts and between contacts to ground. GB/T 5095.2 Method 4a / EIA-364-20B 外观:无击穿和飞弧现象 Appearance: No Breakdown or flashover 6.2.3 温升 Temperature Rise 插合连接器,通以最大允许电流,测温度的差值 Mated connectors and measure the temperature rise of contact when the maximum AC rated current is passed. GB/T 5095.3 Method 5a / EIA-364-70A 30℃ Max. 6.3 环境性能 Environmental 序号 No. 项目Item 测试条件 Test Condition 规格Requirement 6.3.1 耐高温 Heat Resistance 连接器配合后,于85℃的空气中放置
240 小时,再回到 室温中放置 1-2 小时测定 Mated connectors exposed to the condition of 85±2℃ for
240 hours. Recovery time 1~2 hours GB/T 5095.6 Method 11i / EIA-364-17B 外观:无损伤(参照6.1.1) Appearance: No damage.( refer to 6.1.1) 绝缘电阻:500 MΩ Min. Insulation Resistance :500 MΩ Min. 耐电压:800V Min. Withstand Voltage: 800V Min. 6.3.2 耐低温 Cold Resistance 连接器配合后,于-25±2℃的空气中放置
240 小时,再回 到室温中放置 1-2 小时测定 Mated connectors exposed to the condition of -25±2℃ for
240 hours. Recovery time 1~2 hours GB/T 5095.6 Method 11j / EIA-364-17B 外观:无损伤(参照6.1.1) Appearance: No damage.( refer to 6.1.1) 绝缘电阻:500 MΩ Min. Insulation Resistance :500 MΩ Min. 耐电压:800V Min. Withstand Voltage: 800V Min. 6.3.3 恒定湿热 Humidity 温度 40±2℃, 相对湿度(90~95)% 搁置时间 240h,取出恢复 1~2h 后检查. Mated connectors exposed to the condition of 40±2℃ (90~95)% Humidity for
240 hours. Recovery time 1~2 hours GB/T 5095.6 Method 11c /EIA-364-31B 外观:无损伤(参照6.1.1) Appearance: No damage.( refer to 6.1.1) 绝缘电阻:500 MΩ Min. Insulation Resistance :500 MΩ Min. 耐电压:800V Min. Withstand Voltage: 800V Min. 6.3.4 温度循环 Temperature Cycling 把试验样品分别放入高、低温试验箱中,按下列步骤调 试温度: a) 在(-55±2)℃的恒温条件下放置 0.5h;
b) 在(85±2)℃的恒温条件下放置 0.5h;
从a)到b)为一个循环,周期温度转换时间应不大于
5 分钟,共进行
25 个循环,恢复 1~2h 后检查. Mated connectors shall be tested under the following conditions Temperature °C Duration (Minutes)
1 -55
30 2 +25 5Max.
3 +85
30 4 +25 5Max. Step
1 to
4 is one cycle,25 cycles shall be tested. Recovery time 1~2 hours. GB/T 5095.6 method 11d / EIA-364-32C 外观:无损伤(参照6.1.1) Appearance: No damage.( refer to 6.1.1) 绝缘电阻:500MΩ Min. Insulation Resistance :500 MΩ Min. 耐电压:800V Min. Withstand Voltage: 800V Min. 产品规格书 PRODUCT SPECIFICATION 产品名称 Product Name: SAN 编号 Document No. PS3957 版本号 VersionNo.
2 PAGE:
6 /
7 6.3.5 盐雾 Salt Spray 把试验样品从试验箱顶悬挂下来,采用浓度为(5±1)%(质 量百分比)的氯化钠溶液,在(35±2)℃温度下连续雾化 48h,试验后用流动的蒸馏水轻轻洗去表面沉积物. 在常温 常湿条件下恢复 1~2h
48 hours spray, at temp (35±2)℃, Salt NaCl mist (5±1)% After test wash parts and return to room ambient for 1~2 hours GB/T 5095.6 Method 11f /EIA-364-26B 外观:无损伤(五金件应无露出底金属的严重锈蚀;
使用预镀好 的型材,其落料面允许有不影响其性能的轻微腐蚀.) Appearance: No Damage (No erosion with material exposed. And with plating material,slight erosion on the cutting surface is acceptable) 6.3.6 可焊性 Solderability 把试验样品需要焊接的部位浸入焊锡炉中, 锡炉温度(245 ±5)℃,时间(4~5)s Dip solder tails into the molten solder(held at (245±5) ℃ for (4~5) sec. EIA-364-52 上锡率≥90%: Solder coverage: ≥90% 6.3.7 耐焊接热 Resistance to Soldering Heat 把试验样品需要焊接的部位浸入焊锡炉中,锡炉温度 (260±5) ℃;
时间 (5±1) s 后, 在正常条件下恢复 1~2h. Dip solder tails into the molten solder(held at (260±5) ℃ for (5 ±1) sec., Recovery time 1~2 hours 外观:无损伤(参照6.1.1) Appearance: No damage.( refer to 6.1.1) 产品规........