PDF《ILLUMI A T 北极光企业有限公司》

1 High Temperature Operating +70°C 240hrs .No defect of operational function in room temperature are allowable(23±5°C). .Leakage current should be below double of initial value.

2 Low Temperature Operating -20°C 240hrs

3 High Temperature Non-Operating +80°C 240hrs

4 Low Temperature Non-Operating -30°C 240hrs

5 High Temperature / Humidity Non-Operating 60°C ;

90%RH ;

240hrs

6 Temperature Shock Operating -20°C 70°C (30min) (5min) (30min)

50 Cycles

7 Electro-Static Discharge HBM : ±2kv Note 1: Test after

24 hours in room temperature(23±5°C). Note 2: The sampling above is individually for each reliability testing condition. Note 3: The color fading of polarizing filter should not care. Note 4: All of the reliability testing chamber above, is using D.I. water.(Min value:1.0 M?-cm) Note 5: In case of malfunction defect caused by ESD damage, if it would be recovered to normal state after resetting, it would be judged as a good part. I I IL L LL L LU U UM M MI I I A A A T T T I3002-7IX 2440A 16/20 10. Inspection Criteria 10.1 Inspection Conditions 10.1.1 Environmental Conditions The environmental conditions for inspection shall be as follows Room Temperature : 23±5°C Humidity : 50±20%RH 10.1.2 The External Visual Inspection With 1000±200 lux fluorescent lamp as the light source, the inspection was in the distance of 30cm or more from the LCD to the inspector'

s eyes . 10.2 Light Method 1. Inspection is implemented over 30cm vertical distance and 30° incidence under 1000±200 lux. (As showed below) 2. Viewing direction for inspection over 30cm far and is 45° against from LCD ( As showed below) 10.3 Classification of Defects 10.3.1 Major Defect A major defect refers to a defect that may substantially degrade usability for product applications. I I IL L LL L LU U UM M MI I I A A A T T T I3002-7IX 2440A 17/20 10.3.2 Minor Defect A minor defect refers to a defect which is not considered to be able substantially degrade the product application or a defect that deviates from existing standards almost unrelated to the effective use of the product or its operation. Notes: If the LCD/LCM'

s cosmetic and display performance do not specify in inspection criterion , it should be based on these delivered samples. 10.4 Sampling &

Acceptable Quality Level Inspection Item Major Defect Minor Defect Cosmetic 1.0% 1.5% Electrical Test 0.4% 0.65% 10.5 Definition of Inspection Area V/A : Viewing Area A/A : Active Area Active Area Viewing Area Outside of Viewing Area I I IL L LL L LU U UM M MI I I A A A T T T I3002-7IX 2440A 18/20 10.6 Items and Criteria 10.6.1 Visual Inspection Criterion in Cosmetic (1) Glass Defect Glass Defect o Defect Criteria Remark

1 Dimension (Minor) By engineering diagram

2 Cracks (Major) Extensive crack [Reject] (2) LCM Appearance Defect o Defect Criteria Remark

1 Round Type (Minor) Spec. Permissible Q'

ty 1. Ф =(L+W)/2, L: Length, W: Width 2. Disregard if out of A.A. Ф Q0.10mm Disregard 0.10mm<

Ф Q0.20mm

3 0.20mm<

Ф

0 2 Line Type (Minor) Spec. Permissible Q'

ty 1. L: Length, W: Width 2. Disregard if out of A.A. W Q0.03mm Disregard LQ3.0mm and 0.03mm0.10mm or L>

3.0mm

0 3 Polarizer Dent (Minor) Spec. Permissible Q'

ty 1. Ф =(L+W)/2 , L: Length, W: Width 2. Disregard if out of A.A. Ф Q0.20mm Disregard 0.20mm<

Ф Q0.30mm

2 0.30mm<

Ф Q0.50mm

1 0.50mm<

Ф

0 I I IL L LL L LU U UM M MI I I A A A T T T I3002-7IX 2440A 19/20 (3) FPC o Defect Criteria Remark

1 Copper Peeling (Minor) Copper Peeling [Reject] (4) Black Tape o Defect Criteria Remark