PDF《Ultra Low-profile Interface》

2 to

3 ?30 ?2 to

3 min 5% water solution at 35°C for

48 hours 1.Contact resistance 2.Insulation resistance 3.Withstanding voltage 4.Mating/un-mating forces 5. Durability (mating/n-mating) 6. Shock 7. Vibration 8. Temperature cycle 9. Salt spray Characteristic Specification Conditions Series number : LX Termination type

40 : Solder type

60 : Right angle SMT Number of contacts : 12, 16,

20 Contact type P : Male contact (Plug) S : Female contact (Receptacle) Bushing BS(4.0) : Dia. 4.0mm cable BS(4.5) : Dia. 4.5mm cable BS(5.0) : Dia. 5.0mm cable

1 2

3 4

5 3 LX SeriesUltra Low-profile Interface Connectors with 2.0 mm Mounting Height Receptacles Part No. HRS No. Packaging RoHS LX60-12S LX60-16S LX60-20S 245-0018-3 245-0001-0 245-0016-8 2,000 pcs/reel

4 2.55 (5.5) P=0.5 10.6 No.12

2 No.1 ?1 0.8 R0.5 6.5 3.6 (5.5) P=0.5 0.35 1.2 0.3 5.7 1.9 1.9

4 2.8 2-?1.1 Hole 6.5 7.8 1.5 3.8 No conductive traces in this area Land area PCB edge BRecommended PCB mounting pattern

12 pos. P=0.5 (7.5)

5 2 2.55 No.1 12.6 No.16 0.8 ?1 R0.5 6.5 3.6 No conductive traces in this area Land area (7.5) P=0.5 0.35 PCB edge 9.8 8.5 3.8 0.3 5.7 1.9 1.2 1.9

5 2.8 2-?1.1 Hole 1.5 BRecommended PCB mounting pattern

16 pos. (9.5) P=0.5 2.55 6.7 14.6 No.20

2 No.1 0.8 ?1 R0.5 6.5 3.6 1.2 (9.5) P=0.5 0.35 PCB edge 3.8 0.3 5.7 1.9 1.9

7 2.8 2-?1.1 Hole 10.5 11.8 1.5 No conductive traces in this area Land area BRecommended PCB mounting pattern

20 pos.

4 LX SeriesUltra Low-profile Interface Connectors with 2.0 mm Mounting Height ?

5 .

9 14.8 (R3.2) 6.2 21.4 (R1.4) No.12

8 5.1 No.1 Plugs Part No. HRS No. Packaging RoHS LX40-12P LX40-16P LX40-20P 245-0019-6 245-0002-3 245-0017-0

1 12 pos.

16 pos.

20 pos. No.1 (R1.4) 16.8 (R3.8) 21.4 6.2 ?

6 .

4 No.16

8 5.1 21.4 6.2 ( R

1 .

4 ) (R3.8) 18.8 ?

6 .

9 5.5 8.4 No.20 No.1 Bushing Part No. HRS No. Packaging RoHS LX40-12BS(4.0) LX40-16BS(4.5) LX40-20BS(5.0) 245-0020-5 245-0021-8 245-0022-0

100 pcs/pack

5 LX SeriesUltra Low-profile Interface Connectors with 2.0 mm Mounting Height Receptacle Packaging Specifications Embossed carrier tape dimensions Reel dimensions

4 C Unreeling directions

4 2 ?

1 .

5 B 1.75 A (Inside dimension) (Outside dimension) Unreeling directions ?380 ?80 D E

30 ?

1 3 Part No. A B C LX60-12S LX60-16S LX60-20S

24 12 (mm) 11.5 Part No. D E LX60-12S LX60-16S LX60-20S 25.5 29.5 (mm) Receptacles Recommended Temperature Profile Applicable Plug Cable BMated Condition Dimensions Note 1: Applicable cable sizes are guidelines. (There may be slight differences depending on the cable outer insulation) Note 2: Cables must be attached using single piece overmolded bushings on the cable. Note 3: Please refer to applicable Cable Termination Procedures Manual for correct plug assembly and cable termination. Note 4: Contact HRS for cable assemblies. ? '

*% '

%% &

*% &

%% *% &

-%? &

*%? '

(%?b^c# .%¤(%h (%¤&

%h E:6@/'

*%? * % 0.5 Plug

2 1.4 (mm) Receptacle

2 This measurement is performed on the contact lead section. The temperature profile may vary due to external conditions such as the type of cream solder, manufacturer, and board size. Please contact the solder manufacturer for their specifications. Cable diameter Wire size Part No. ?4 max. ?4.5 max. ?5 max. ?0.6 mm max. (AWG#30 to

32 or equivalent) LX40-12P LX40-16P LX40-20P (mm)

6 LX SeriesUltra Low-profile Interface Connectors with 2.0 mm Mounting Height The characteristics and the specifications contained herein are for reference purpose. Please refer to the latest customer drawings prior to use. The contents of this catalog are current as of date of 09/2014. Contents are subject to change without notice for the purpose of improvements. USA: HIROSE ELECTRIC (U.S.A.), INC. San Jose Office