PDF《CERTAPRO Thermal》

Specification Sheet 1.

PRODUCT NAME CertainTeed CERTAPRO? Thermal FSK-25 Faced Batts 2. MANUFACTURER CertainTeed Corporation P.O. Box

860 Valley Forge, PA 19482-0105 Phone: 610-341-7000 800-233-8990 Fax: 610-341-7571 Fax-On-Demand: 800-947-0057 Website: www.certainteed.com 3. PRODUCT DESCRIPTION Basic Use: These light density batts enhance thermal performance in exterior and interior walls and floor/ceiling assemblies. FSK-25 faced batts are UL listed for Fire Hazard Classification (FHC) 25/50, and are intended for exposed appli- cations in commercial construction where a vapor retarder is needed. Benefits: Installing CertaPro Thermal FSK-25 faced Batts can save energy and help control building operat- ing costs. The product also provides enhanced acoustical performance, contributing to a quieter interior envi- ronment. The product resists bacteria and fungal growth and will not rot or deteriorate. CertaPro Thermal FSK-25 faced Batts are lightweight and will not settle or sag. Composition and Materials: This product is made from inorganic glass fibers bonded with a thermoset resin to form a uniformly textured, yellow blanket insulation. A flame- resistant foil-scrim-kraft (FSK) facing is adhered to the fiber glass. Limitations: The National Electrical Code prohibits installation of insula- tion over or within

3 (76 mm) of recessed light fixtures, unless approved insulated ceiling (IC) lighting fixtures are used. Insulation should be kept clean and dry at all times. Sizes: Available as shown in the table below. Contact CertainTeed for other sizes and minimum order quantities. 4. TECHNICAL DATA Applicable Standards: ? Model Building Codes: C New York City C MEA 19-80-M C California Quality Standards. Reg. No. CA-T024 (PA) C City of Los Angeles, RR

8148 ? Material Standards: C (ASTM C 553) Type I C (ASTM C 665) Type III, Class A, Category

1 ? GREENGUARD Certification Standards: C Low Emitting Products for the Indoor Environment C Product Emission Standard for Children and Schools Fire Resistance: ? Surface Burning Characteristics: C (ASTM E 84, UL 723, NFPA 255) Max. Flame Spread Index;

25 Max. Smoke Dev. Index;

50 ? Noncombustibility: C (ASTM E 136) Pass Physical/Chemical Properties: ? Thermal Performance: C (ASTM C

177 or ASTM C 518) See the table below. ? Maximum Use Temperature: C Temperature: (ASTM C 411) 250°F (121°C) ? Water Vapor Sorption: C (ASTM C 1104) ≤ 3% by weight ? Water Vapor Permeance: C Permeance of Facing: (ASTM E 96) ≤ 0.02 perms (1.1 ng/Pa?s?m2) ? Corrosiveness: C (ASTM C 665) Pass ? Fungi Resistance: C (ASTM C 1338) Pass ? Odor Emission: C (ASTM C 1304) Pass Quality Assurance: CertainTeed was the first fiber glass insulation manufacturer to have its manufactur- ing plants, R&

D?center and corporate headquarters registered to ISO 9001-

2000 standards. 5. INSTALLATION On exterior walls the faced side of the insulation should be installed toward the interior side of the structure, except in hot, humid areas where local code regulations may require a vapor retard- er to face toward the exterior. In steel stud construction, insulation is friction fitted into stud cavities prior to apply- ing the interior finish. FSK-25 faced batts can also be applied to masonry walls and under roof decks with pins and washers. FSK-25 faced products in wood stud construction should be sta- CERTAPRO ? Thermal FSK-25 Faced Batts pled approximately every

8 (200mm). Follow the pin manufacturer'

s recom- mendations for pin terminations and safety considerations. These installa- tion recommendations are general in nature. Other methods are acceptable. Please consult your contractor for rec- ommendations best suited to specific applications. 6. AVAILABILITY AND COST Manufactured and sold throughout the United States. For availability and cost, contact your local contrac- tor, distributor, or call CertainTeed Sales Support Group in Valley Forge, PA at 800-233-8990. 7. WARRANTY Refer to CertainTeed'