PDF《GBM Professional》

Robert Bosch GmbH Power Tools Division

70745 Leinfelden-Echterdingen Germany www.

bosch-pt.com

1 619 P08

930 (2010.05) O /

23 XXX GBM Professional

350 |

350 RE en Original instructions cn 正本使用说明书 id Petunjuk-Petunjuk untuk Penggunaan Orisinal OBJ_DOKU-9059-004.fm Page

1 Monday, May 10,

2010 1:04 PM

2 |

1 619 P08

930 | (10.5.10) Bosch Power Tools English.Page

4 中文 页11 Bahasa Indonesia Halaman

16 OBJ_BUCH-527-004.book Page

2 Monday, May 10,

2010 1:11 PM |

3 Bosch Power Tools

1 619 P08

930 | (10.5.10) B A GBM

350 RE Professional

1 2

3 4

6 8

7 5 OBJ_BUCH-527-004.book Page

3 Monday, May 10,

2010 1:11 PM

4 | English

1 619 P08

930 | (10.5.10) Bosch Power Tools en Safety Notes General Power Tool Safety Warnings Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in elec- tric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term power tool in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. 1) Work area safety a) Keep work area clean and well lit. Clut- tered or dark areas invite accidents. b) Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes. c) Keep children and bystanders away while operating a power tool. Distrac- tions can cause you to lose control. 2) Electrical safety a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock. b) Avoid body contact with earthed or grounded surfaces, such as pipes, radia- tors, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded. c) Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock. d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges and moving parts. Damaged or entangled cords increase the risk of electric shock. e) When operating a power tool outdoors, use an extension cord suitable for out- door use. Use of a cord suitable for out- door use reduces the risk of electric shock. f) If operating a power tool in a damp loca- tion is unavoidable, use a residual cur- rent device (RCD) protected supply. Use of an RCD reduces the risk of electric shock. 3) Personal safety a) Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influ- ence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious person- al injury. b) Use personal protective equipment. Al- ways wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protec- tion used for appropriate conditions will reduce personal injuries. c) Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or bat- tery pack, picking up or carrying the tool. Carrying power tools with your fin- ger on the switch or energising power tools that have the switch on invites acci- dents. d) Remove any adjusting key or wrench be- fore turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal inju- ry. e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unex- pected situations. f) Dress properly. Do not wear loose cloth- ing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts. WARNING OBJ_BUCH-527-004.book Page

4 Monday, May 10,

2010 1:11 PM English |

5 Bosch Power Tools

1 619 P08

930 | (10.5.10) g) If devices are provided for the connec- tion of dust extraction and collection fa- cilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards. 4) Power tool use and care a) Do not force the power tool. Use the cor- rect power tool for your application. The correct power tool will do the job better and safer at the rate for which it was de- signed. b) Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be re- paired. c) Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjust- ments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally. d) Store idle power tools out of the reach of children and do not allow persons unfa- miliar with the power tool or these in- structions to operate the power tool. Power tools are dangerous in the hands of untrained users. e) Maintain power tools. Check for mis- alignment or binding of moving parts, breakage of parts and any other condi- tion that may affect the power tool'

s op- eration. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. f) Keep cutting tools sharp and clean. Prop- erly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. g) Use the power tool, accessories and tool bits etc. in accordance with these in- structions, taking into account the work- ing conditions and the work to be per- formed. Use of the power tool for operations different from those intended could result in a hazardous situation. 5) Service a) Have your power tool serviced by a qual- ified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. Safety Warnings for Drills f Hold power tool by insulated gripping sur- faces, when performing an operation where the cutting accessory may contact hidden wiring or its own cord. Cutting accessory contacting a live wire may make exposed metal parts of the power tool live and could give the operator an electric shock. f Use appropriate detectors to determine if utility lines are hidden in the work area or call the local utility company for assistance. Contact with electric lines can lead to fire and electric shock. Damaging a gas line can lead to explosion. Penetrating a water line causes property damage or may cause an electric shock. f Switch off the power tool immediately when the tool insert jams. Be prepared for high reaction torque that can cause kick- back. The tool insert jams when: ― the power tool is subject to overload or ― it becomes wedged in the workpiece. f Secure the workpiece. A workpiece clamped with clamping devices or in a vice is held more secure than by hand. f Keep your workplace clean. Blends of mate- rials are particularly dangerous. Dust from light alloys can burn or explode. f Always wait until the machine has come to a complete stop before placing it down. The tool insert can jam and lead to loss of control over the power tool. f Never use the machine with a damaged ca- ble. Do not touch the damaged cable and pull the mains plug when the cable is dam- aged while working. Damaged cables in- crease the risk of an electric shock. OBJ_BUCH-527-004.book Page

5 Monday, May 10,

2010 1:11 PM

6 | English

1 619 P08

930 | (10.5.10) Bosch Power Tools Products sold in GB only: Your product is fitted with an BS 1363/A approved electric plug with internal fuse (ASTA approved to BS 1362). If the plug is not suitable for your socket outlets, it should be cut off and an appropriate plug fit- ted in its place by an authorised customer serv- ice agent. The replacement plug should have the same fuse rating as the original plug. The severed plug must be disposed of to avoid a possible shock hazard and should never be in- serted into a mains socket elsewhere. Products sold in AUS and NZ only: Use a resid- ual current device (RCD) with a rated residual current of

30 mA or less. Functional Description Read all safety warnings and all in- structions. Failure to follow the warnings and instructions may re- sult in electric shock, fire and/or se- rious injury. While reading the operating instructions, unfold the graphics page for the machine and leave it open. Intended Use The machine is intended for drilling in wood, metal, ceramic and plastic. Machines with elec- tronic control and right and left rotation are also suitable for screwdriving and tapping. Product Features The numbering of the product features refers to the illustration of the machine on the graphics page.

1 Key type drill chuck

2 Lock-on button for On/Off switch

3 On/Off switch

4 Rotational direction switch(GBM

350 RE)

5 Handle (insulated gripping surface)

6 Chuck key

7 Screwdriver bit*

8 Universal bit holder* *Accessories shown or described are not part of the standard delivery scope of the product. A complete overview of accessories can be found in our acces- sories program. OBJ_BUCH-527-004.book Page

6 Monday, May 10,

2010 1:11 PM English |

7 Bosch Power Tools

1 619 P08

930 | (10.5.10) Technical D........