PDF《产品规格书》

1 min between adjacent terminal or ground. 外观:无击穿和飞弧现象 Appearance: No Breakdown 5.2.4 温升 Temperature Rise 插合连接器,通以额定电流. Carrying rated current loading. 30℃ Max. 5.3 环境性能 Environmental 序号 No. 项目Item 测试条件 Test Condition 规格Requirement 5.3.1 耐高温 Heat Resistance 连接器配合后, 于105±2℃的空气中放置

96 小时, 再回到室温中放置 1-2 小时测定. Mated connectors are exposed to a temperature of

105 ±2℃ for

96 hours. 外观:无损伤 Appearance: No Damage 绝缘电阻:500MΩ Min. Insulation Resistance: 500MΩ Min. 接触电阻:0.02ΩMax. Low Level Contact Resistance:0.02ΩMax. 5.3.2 耐低温 Cold Resistance 连接器配合后,于-40±3℃的空气中放置

96 小时, 再回到室温中放置 1-2 小时测定. Mated connectors are exposed to a temperature of -40 ±3℃ for

96 hours. 外观:无损伤 Appearance: No Damage 绝缘电阻:500MΩ Min. Insulation Resistance: 500MΩ Min. 接触电阻:0.02Ω Max. Low Level Contact Resistance:0.02Ω Max. 5.3.3 恒定湿热 Humidity 温度(60±2)℃,相对湿度(90~95)%, 搁置时间 96h, 取出恢复 2h 后检查. Temperature: (60±2)℃;

Relative Humidity: (90~ 95)%;

Duration: 96h 外观:无损伤 Appearance: No Damage 接触电阻:0.02Ω Max. Low Level Contact Resistance:0.02Ω Max. 耐电压:1500V Dielectric Strength: 1500V 绝缘电阻:500MΩ Min. Insulation Resistance: 500MΩ Min. Page

8 of

8 产品规格书 Product Specification 编号Serial number PS3347 版本号Version Number

2 产品名称 Product Name TJC65002-nAD 阳连接器 产品编码 Part Number 见附表 5.3.4 温度循环 Temperature Cycling 把试验样品分别放入高、低温试验箱中,按下列步 骤调试温度: a) 在(-55±2)℃的恒温条件下放置 0.5h;

b) 在(105±2)℃的恒温条件下放置 0.5h;

从a)到b)为一个循环周期,共进行

5 个循环,恢复 1h 后检查.状态转换时间不多于

1 小时.

5 cycles of: a) (-55±2)℃ 0.5h b) (105±2)℃ 0.5h Normal temperature and relative humidity 1h. Transition time should be less than 1h. 外观:无损伤 Appearance: No Damage 接触电阻:0.02Ω Max. Low Level Contact Resistance:0.02Ω Max. 绝缘电阻:500MΩ Min. Insulation Resistance: 500MΩ Min. 5.3.5 盐雾 Salt Spray 把试验样品从试验箱顶悬挂下来,采用浓度为(5± 1)%(质量百分比)的氯化钠溶液,在35±2 ℃条件 下连续雾化 48h,试验后用流动的蒸溜水轻轻洗去表 面沉积物,在常温常湿条件下恢复 1~2h. 48h exposure to a salt spray from the (5 ±1)% solution at 35±2 ℃ 外观: 无损伤(五金件应无露出底金属的严 重锈蚀;

使用预镀好的型材, 其落料面允许 有不影响其性能的轻微腐蚀) Appearance:No Damage (No erosion with material exposed. And with plating material, slight erosion on the cutting surface is acceptable) 接触电阻:0.02Ω Max. Low Level Contact Resistance:0.02Ω Max. 5.3.6 可焊性 Solderability 把试验样品需要焊接的部位浸入焊锡炉中,锡炉温 度(240±3)℃,时间(3±0.5)s. Soldering Time: (3±0.5)s Solder Temperature: (240±3)℃ 上锡率≥90% 90% of immersed area must show no voids, pin holes 5.3.7 耐焊接热 Resistance to Soldering Heat 把试验样品需要焊接的部位浸入焊锡炉中,锡炉温 度(260±5)℃;

时间(5±0.5)s 后,在正常条件 下恢复 1h. Soldering Time: (5±0.5)s Solder Temperature: (260±5)℃ 外观: 无损伤 Appearance: No Damage

6 插拔力 Insertion / Withdrawal force 极数 No.of CKT. 插入力(最大值) Insertion force (Max.) 拔出力(最小值) Withdrawal force (Min.) 初次 1st 第6次6th 第30 次30th 初次 1st 第6次6th 第30 次30th