PDF《MODEL NO.: V201V1-T03》

3050 3150

3250 g - Note (1) Please refer to the attached drawings for more information of front and back outline dimensions. www.SpecLcd.com www.SpecLcd.com Issued Date: May 16,

2005 Model No.: V201V1-T03 Preliminary

5 The information described in this technical specification is tentative and it is possible to be changed without prior notice. Please contact CMO '

s representative while your product design is based on this specification. Version1.0 2. ABSOLUTE MAXIMUM RATINGS 2.1 ABSOLUTE RATINGS OF ENVIRONMENT Value Item Symbol Min. Max. Unit Note Storage Temperature TST -20 +60 ?C (1) Operating Ambient Temperature TOP

0 50 ?C (1), (2) Shock (Non-Operating) SNOP -

50 G (3), (5) Vibration (Non-Operating) VNOP - 1.0 G (4), (5) Note (1) Temperature and relative humidity range is shown in the figure below. (a)

90 %RH Max. (Ta Q

40 ?C). (b) Wet-bulb temperature should be

39 ?C Max. (Ta >

40 ?C). (c) No condensation. Note (2) The temperature of panel display area surface should be

0 ?C Min. and

60 ?C Max. Note (3)

11 ms, half sine wave,

1 time for ± X, ± Y, ± Z. Note (4)

10 ~

500 Hz,

10 min,

1 time each X, Y, Z. Note (5) At testing Vibration and Shock, the fixture in holding the module has to be hard and rigid enough so that the module would not be twisted or bent by the fixture. Relative Humidity (%RH) Operating Range Temperature (?C)

100 80

60 -20

40 0

20 -40

90 80

40 60

20 10 Storage Range www.SpecLcd.com www.SpecLcd.com Issued Date: May 16,

2005 Model No.: V201V1-T03 Preliminary

6 The information described in this technical specification is tentative and it is possible to be changed without prior notice. Please contact CMO '

s representative while your product design is based on this specification. Version1.0 2.2 ELECTRICAL ABSOLUTE RATINGS 2.2.1 TFT LCD MODULE Value Item Symbol Min. Max. Unit Note Power Supply Voltage Vcc -0.3 +6.0 V 2.2.2 BACKLIGHT UNIT Value Item Symbol Min. Max. Unit Note Lamp Voltage VL -

3000 VRMS Lamp Current IL - 7.0 MARMS Lamp Frequency FL

20 80 KHz 3. ELECTRICAL CHARACTERISTICS 3.1 TFT LCD MODULE Ta =

25 ±

2 ?C Value Parameter Symbol Min. Typ. Max. Unit Note Power Supply Voltage Vcc 4.5 5.0 5.5 V (1) Ripple Voltage VRP -

80 - mV (2) Rush Current IRUSH - 1.8 - A White - 0.23 - A Black - 0.34 - A Power Supply Current Vertical Stripe lcc - 0.32 - A (3) TTL input high threshold voltage VIH 2.3 - 3.3 V TTL input low threshold voltage VIL

0 -

1 V Note (1) The module should be always operated within above ranges. Note (2) Measurement Conditions: R1 (High to Low) (Control Signal) +12V SW Q2 C1 1uF Vcc +5.0V 2SK1470 Q1 2SK1475 47K R2 1K VR1 47K C2 0.01uF C3 1uF FUSE (LCD Module Input) www.SpecLcd.com www.SpecLcd.com Issued Date: May 16,

2005 Model No.: V201V1-T03 Preliminary

7 The information described in this technical specification is tentative and it is possible to be changed without prior notice. Please contact CMO '

s representative while your product design is based on this specification. Version1.0 Note (3) The specified power supply current is under the conditions at Vcc =

5 V, Ta =

25 ±

2 ?C, fv =

60 Hz, whereas a power dissipation check pattern below is displayed. Vcc rising time is 470?s 470?s +5V GND 0.9Vcc 0.1Vcc Active Area a. White Pattern Active Area c. Vertical Stripe Pattern R R R R ........