PDF《产品规格书》

1.0 照明: (200~300)lx Lamp: (200~300)lx 目测距离: (0.3~0.5)m Space: (0.3~0.5)m GB/T 5095.1 Method 1a 1.塑料件表面应无明显疤痕、凹陷、开裂及影响使用的变形. Plastic part: smooth and flat surface without discolor, broken, crack, and distortion, etc.

2 金属件表面无锈蚀、 氧化 、 无明显的机械损伤及电镀层脱落等缺 陷. Metal part: bright and even surface without rust, oxide, fog and obvious physical damage, etc. 6.1.2 针的固定力 Retention Force for Pin 固定连接器和测力计,在连接器轴线方向施加规定 的推力进行测试,

25 mm/min. Apply thrust force on the Pin in the wafer at a rate less than

25 mm/min . GB/T 5095.8 Method 15a / EIA-364-29B 4.9NMin 额定电流 Rated Current 1A [AC(有效值 rms)/DC] 额定电压 Rated Voltage 200V [AC(有效值 rms)/DC] 使用温度范围(包含温升) Operating temperature range (Include temperature rise) -40℃~+70℃ 产品规格书 PRODUCT SPECIFICATION 产品名称 Product Name: IL-Z-nP-CLIP0.5-C/ IL-Z-nP-CLIP-E-C 编号 Document No. PS4017 版本号 VersionNo.

1 PAGE:

4 /

7 6.1.3 插拔力 Insertion / withdrawal force 连接器相配,以1mm/s~5mm/s的速度 沿接插器轴线方向插入和拔出. Insert and withdraw connectors at the speed rate of 1mm/s~5mm/s PIN 插入力 (Insertion) MAX 固定力(Retention) MIN 7P 44N 7.4N 9P 55N 8.3N 15P 83N 11.3N 6.1.4 机械寿命 Durability 以每分钟

10 次的速度插拔

50 次. Fifty cycles for mating and unmating test at the speed of

10 cycles per minute GB/T 5095.5 Method 9a / EIA-364-09C 外观:无损伤(参照6.1.1) Appearance: No damage.( refer to 6.1.1) 接触电阻:0.04Ω Max. Contact resistance: 0.04Ω Max. 6.1.5 机械振动 Random Vibration 插合连接器,串联在一直流电源上,电流100mA;

并 模拟正常工作状态;

振频为(10~55~10)Hz, 每个循环时间为1分钟,振幅1.52mm.沿XYZ 三轴正反方向各循环2h. Mate connectors subjected them to following vibration conditions, for a period of

2 hours in each of

3 mutually perpendicular axes,

100 mA current shall be applied. Frequency: (10~55~10)HZ/min. Amplitude: 1.52mm GB/T 5095.4 Method 6d / EIA-364-28D 外观:无损伤(参照6.1.1) Appearance: No damage.( refer to 6.1.1) 接触电阻:0.04Ω Max. Contact resistance: 0.04Ω Max. 中断(当电阻大于7Ω): 1μsec Max. 7Ω) 6.1.6 机械冲击 Shock 连接器相配,沿XYZ三轴正反方向各冲击3次(总共 18次),在测试过程中通以100mA电流. 冲击强度:490m/s2 持续时间:11ms Mate connectors and subject them to the following shock conditions,

3 times of shock shall be applied for each

6 directions along

3 mutually perpendicular axes, passing DC 100mA current during the test.(Total of

18 shocks) Test Pulse: : 490m/s2 Duration: 11ms GB/T 5095.4 Method 6c / EIA-364-27B 外观:无损伤(参照6.1.1) Appearance: No damage.( refer to 6.1.1) 接触电阻:0.04Ω Max. Contact resistance: 0.04Ω Max. 中断(当电阻大于7Ω): 1μsec Max. 7Ω) 6.2 电气性能 Electrical 序号 No. 项目Item 测试条件 Test Condition 规格 Requirement 6.2.1 接触电阻 Contact Resistance 端子与导线按要求压着后,用小功率电路进行测试端子压着部 位的接触电阻. Mate connectors with dry circuit to test Contact resistance of crimping. GB/T 5095.2 Method 2b / EIA-364-23B 0.02ΩMax 6.2.2 绝缘电阻 Insulation Resistance 在相邻接触件之间或地线之间,用500V DC 电压进行测试. Apply a voltage of 500V DC between adjacent contacts and between contacts to ground. GB/T 5095.2 Method 3a / EIA-364-21C