PDF《产品规格书》

100 MΩ Min. ( Initial)

50 MΩ Min. (Final) 6.2.3 耐电压 Withstand Voltage 相邻接触件之间或地线之间施加 500V AC (有效值),漏电 流1mA 的电压作用,时间 1min. Apply a voltage of AC 500V for

1 minute between adjacent contacts and between contacts to ground. GB/T 5095.2 Method 4a / EIA-364-20B 外观:无击穿和飞弧现象 Appearance: No Breakdown or flashover 产品规格书 PRODUCT SPECIFICATION 产品名称 Product Name: IL-Z-nP-CLIP0.5-C/ IL-Z-nP-CLIP-E-C 编号 Document No. PS4017 版本号 VersionNo.

1 PAGE:

5 /

7 6.3 环境性能 Environmental 序号 No. 项目Item 测试条件 Test Condition 规格Requirement 6.3.1 耐高温 Heat Resistance 连接器配合后,于70±2℃的空气中放置

96 小时, 再回到室温中放置 1~2 小时测定 Mated connectors exposed to the condition of 70±2℃ for96 hours. Recovery time 1~2hours GB/T 5095.6 Method 11i / EIA-364-17B 外观:无损伤(参照6.1.1) Appearance: No damage.( refer to 6.1.1) 接触电阻:0.04Ω Max. Contact resistance: 0.04Ω Max. 6.3.2 恒定湿热 Humidity 温度 40±2℃, 相对湿度(90~95)% 搁置时间 96h,取出测试绝缘电阻,2h 后测试接 触电阻、耐电压、绝缘电阻. Mated connectors exposed to the condition of temperature 40±2℃, humidity (90~95)% for

1000 hours. Test insulation resistance, 2h later test contact resistance, insulation resistance, withstand voltage GB/T 5095.6 Method 11c /EIA-364-31B 外观:无损伤(参照6.1.1) Appearance: No damage.( refer to 6.1.1) 接触电阻:0.04Ω Max. Contact resistance: 0.04Ω Max. 绝缘电阻:50 MΩ Min. Insulation Resistance :50 MΩ Min. 耐电压:250V Min. Withstand Voltage: 20V Min. 6.3.3 温度循环 Temperature Cycling 把试验样品分别放入高、低温试验箱中,按下列 步骤调试温度: a) 在(-55±2)℃的恒温条件下放置 0.5h;

b) 在(85±2)℃的恒温条件下放置 0.5h;

从a)到b)为一个循环,周期温度转换时间应不大 于5分钟,共进行

25 个循环,恢复 1~2h 后检查. Mated connectors shall be tested under the following conditions Temperature °C Duration (Minutes)

1 -55

30 2 +25 5Max.

3 +85

30 4 +25 5Max. Step

1 to

4 is one cycle,25 cycles shall be tested. Recovery time 1~2 hours. GB/T 5095.6 method 11d / EIA-364-32C 外观:无损伤(参照6.1.1) Appearance: No damage.( refer to 6.1.1) 接触电阻:0.04Ω Max. Contact resistance: 0.04Ω Max. 绝缘电阻:50 MΩ Min. Insulation Resistance :50 MΩ Min. 耐电压:250V Min. Withstand Voltage: 250V Min. 6.3.3 盐雾 Salt Spray 把试验样品从试验箱顶悬挂下来,采用浓度为 (5±1)%(质量百分比)的氯化钠溶液,在(35±2)℃温 度下连续雾化 48h,试验后用流动的蒸馏水轻轻洗 去表面沉积物.在常温常湿条件下恢复 1~2h Forty-eight hours spray, at temp (35±2)℃, NaCl mist concentration (5±1)%. After test, wash parts and put it into room ambient for 1~2 hours GB/T 5095.6 Method 11f /EIA-364-26B 外观:无损伤(五金件应无露出底金属的严重锈蚀;

使用预镀 好的型材,其落料面允许有不影响其性能的轻微腐蚀.) Appearance: No Damage (No erosion on material exposed. and plating material, slight erosion on the cutting surface is acceptable) 接触电阻:0.04Ω Max. Contact resistance: 0.04Ω Max. 6.3.5 可焊性 Solderability 把试验样品需要焊接的部位浸入焊锡炉中,锡炉 温度(235±5)℃,时间(2±1)s Dip solder tails into the molten solder held at (235±5) ℃for ((2±1) sec. EIA-364-52 上锡率≥90%: Solder coverage: ≥90% 产品规格书 PRODUCT SPECIFICATION 产品名称 Product Name: IL-Z-nP-CLIP0.5-C/ IL-Z-nP-CLIP-E-C 编号 Document No. PS4017 版本号 VersionNo.