PDF《高清网络摄像机快速安装指南》

1 Installation Steps 2. Connect the cable and power on. 1. Remove the dust cover and mount the lens. CS type lens can be mounted directly, while an adapter ring is needed before mounting C type lens, as the picture shows. [Note]: Back focus adjustment is unavailable for this series. OUT G IN G O1 O2 I1 I2 B A RS485 LAN Micro SD DC 12V VIDEO OUT RUN LINK ALARM AUDIO RS485 Port Video Out -AS model supports HD-SDI, -Other models support CVBS TF Card Slot Max. Memory 32G Power Port, DC12V Network Port some models support PoE Indicator Lamp Audio In/Out Alarm In/Out [Note]: RUN Lamp: operation indicator, green, ?ashes after power on (1s on, 1s off), and turns off after power off. LINK Lamp: network status indicator, green, turns on after power on and network connected, and turns off after power off or network disconnected. If the lens does not focus well after adjustment, try to mount a spacer. DC IRIS, for Auto IRIS lens Mount an adapter ring for C type lens If the lens does not focus well after adjustment, try to mount a spacer. DC IRIS, for Auto IRIS lens

2 3. Login client System for client installation: Processor: 2.0 GHz CORE?2 series or other equivalent processors RAM Memory: 2GB or above Operating System: Windows XP or newer version Browser: IE6.0 or newer version DirectX:9.0c [Note]: This Guide will take Windows XP as example to explain client login steps. 1) The factory default IP of camera is 0.0.0.0. Please set the camera and the PC in the same LAN and use IPCSearch to con?gure IP. If the network provides DHCP service, DHCP server will con?gure IP for the camera automatically.

3 2) Run IPCSearch, select the target camera, and click Modify Params. When con?gure a static IP for the camera, please check Custom device address (Close DHCP) and ?ll the Ethernet parameter. After con?guration, the camera will reboot automatically and this takes 60s. 3) After reboot, user can click Login to login web client. If IP con?guration has been ?nished, user can input camera IP address in IE to go to web client. 4) Enter default admin user name and password, both of which are admin , or operator user name and password, both of which are guest . [Note]: When run web client for the ?rst time, please download and install video ActiveX control. If user fails to download the ActiveX control, operate as follows: 1) Click Internet Options>

Security . 2) Click Trusted Sites>

Sites , input the IP address of this camera and add. [Note]: When add an address, uncheck Require server veri?cation (https:) for all sites in this zone . If operate under Windows

7 or Vista system, make sure that the UAC service has been disabled.

4 1) Run Start>

Operate>

mscon?g>

Tool , select Modify UAC Setting , and click Enable . 2) Drag the slider to the bottom, click OK and reboot PC. After con?guration, please input the IP address of the camera in IE, and install the ActiveX control to login IPCCtrl. 4. Live view and lens adjustment After login, user can view live video directly, as the picture shows. [Note]: Please refer to the help ?le of IPCCtrl for detailed explanation. Adjust camera direction, rotate lens knob to adjust camera focus and zoom until the live view meets requirement. [Note]: Please apply the maximum aperture before adjusting camera focus and zoom.

5 Bracket Installation When mount the camera on a ceiling mount bracket, the bracket adapter can be taken apart from the bottom and be mounted on the top of the camera, as the picture shows. Screw Bracket Adapter Camera Top View Housing Installation When the camera works outdoor, it should be installed in a water-proof housing, explanation as follows: 1. Unscrew the snap-?t and open the cover of the housing, as the picture shows. 2. Use a screwdriver to loosen the screws on the holder, pull the holder backward and take it from the holes. [Note]: Only unscrew the screws on the holder, no need to screw them off. 3. Route the cable and screw up the PG joint. 4. Place the holder at the bottom of the camera. 5. Install the camera and the holder in the housing. [Warning]: Before ?xing, put the camera lens close to the window of the housing without any obvious gap (gap only enough for focus), to avoid light leak or halo. 6. Wire camera connectors to the connector board of the housing, cover the housing and lock it up. Snap-?t Holder Hole PG Joint Screw Hole Holder Camera