编辑: ddzhikoi | 2019-07-13 |
140 127 030Q0200 3030PM
76 130 C
181 165
156 030Q0210 3030KM
20 x
12 191
175 159 030R0200 3535PM
89 160 C
225 203
191 030R0210 3535KM
22 x
12 235
213 200 030S0200 4040PM
102 185 C
275 248
229 030S0210 4040KM
24 x
12 285
257 238 D3 D2 L1 D D2 D1 L1 L3 L2 D3 D4 D2 D5 D1 L4 L1 L3 L2
6 holes equally spaced to suit B dia. bolts Hub ref. PM has Plain OD KM has Keywayed OD Section :
6 shaft fixings Taper Lock? Hubs and Adaptors Product Code Size Use Bush Size L1 L2 L3 L4 B 017C0010 BF12
1210 25
10 6.5 2.5 M6 017G0010 BF16
1610 25
10 6.5 2.5 M6 017K0010 BF20
2012 32
13 8.5 2.5 M8 017M0010 BF25
2517 44
20 11.5 2.5 M10 017P0010 BF30
3020 50
20 11.5 2.5 M12
128 Taper Lock? Hubs and Adaptors shaft fixings Section :
6 WELD-ON-HUBS Fenner Taper Lock Weld-on Hubs are made of steel, grade 070M20, drilled, tapped and taper bored to receive standard Taper Lock bushes. The shouldered outer diameter provides a convenient means of welding hubs into fan rotors, steel pulleys, plate sprockets, impellers, agitators and many other devices which must be firmly fastened to the shaft. *Bore tolerance of D2 +0mm/-0.05mm is recommended Product Code Size UseBush Size D1 D2 * D3 L1 L2 L3 025C0010 WH12
1210 70
65 64.5
25 9
10 025G0010 WH16
1610 80
75 74.5
25 9
10 025K0010 WH20
2012 95
90 89.5
32 12
12 025M0010 WH25
2517 115
110 109.5
44 19
15 025P0010 WH30
3020 145
140 139.5
50 20
15 025J0010 WH35
3525 190
180 179.5
65 25
25 025X0010 WH40
4030 200
190 189.5
76 32
30 025Y0010 WH45
4535 210
200 199.5
89 40
30 025Z0010 WH50
5040 230
220 219.5
102 40
35 D3 D2 L1 D2 D1 L1 L3 L2 D3 D4 D2 D5 D1 L4 L1 L3 L2
6 holes equally spaced to suit B dia. bolts Welding instructions Fenner Taper Lock Weld-on Hubs are made of steel, are machined to accept Taper Lock bushes for shaft fixing, and have a precision machined shoulder against which flanges or webs can be located. It is recommended that a continuous 45° mitre weld be used, working on the larger hub diameter section only. To ensure accuracy in the welded assembly it is essential to apply only sufficient weld to achieve sufficient strength. Excess weld should not be necessary for normal use and, due to greater heat input, gives a higher risk of distortion. The table below shows recommended continuous fillet weld requirements for each hub size. Hub No Leg Length mm WH12
4 WH16
4 WH20
5 WH25
5 WH30
6 WH35
6 WH40
8 WH45
8 WH50
10 Leg Length For electric arc welding, low hydrogen electrodes are recommended FEN01/14 : Drive Design &
Maintenance Manual
129 Bore Dia Keyway Shallow Keyway Depth Product Code Width Depth
3525 3535
4030 4040
4535 4545
5040 5050
35 10 3.3 C 029J0035 029R0035
38 10 3.3 C 029J0038 029R0038
40 12 3.3 C 029J0040 029R0040 029X0040 029S0040
42 12 3.3 C 029J0042 029R0042 029X0042 029S0042
45 14 3.8 C 029J0045 029R0045 029X0045 029S0045
48 14 3.8 C 029J0048 029R0048 029X0048 029S0048
50 14 3.8 C 029J0050 029R0050 029X0050 029S0050
55 16 4.3 C 029J0055 029R0055 029X0055 029S0055 029Y0055 029T0055
60 18 4.4 C 029J0060 029R0060 029X0060 029S0060 029Y0060 029T0060
65 18 4.4 C 029J0065 029R0065 029X0065 029S0065 029Y0065 029T0065
70 20 4.9 C 029J0070 029R0070 029X0070 029S0070 029Y0070 029T0070 029Z0070 029U0070
75 20 4.9 C 029J0075 029R0075 029X0075 029S0075 029Y0075 029T0075 029Z0075 029U0075
80 22 5.4 C 029J0080 029R0080 029X0080 029S0080 029Y0080 029T0080 029Z0080 029U0080