PDF《DC Input》

JetWave

2316 Series Industrial Cellular + 802.

11n 2.4G WIFI IP Gateway, 4xGT+2G SFP Quick Installation Guide V1.0 JetWave

2316 is an industrial grade Secure Cellular + 802.11n 2.4G WIFI IP Gateway with 4xGT + 2G SFP Switch ports, which enables multiple Ethernet ports and RS232-422-485 serial port access over LTE network. R&

TTE Directive 1999/5/EC Declaration The product may be operated in all European Union countries. While you see the CE Marking printed on our product, it indicates the product complies with the requirement of the R&

TTE (1995/5/EC) Directive. You can download the formal document of the product from our Web site or send inquiry to our Sales/Technical people. Band Information General Requirement Only trained and qualified personnel should be allowed to install, replace, or service this equipment. The device can only be operated according to the technical specification. Read the installation instructions/user manual, including Power, Cable, Antenna, Warning info and well Grounding is must before connecting the system to the power source. DC Input Insert the positive and negative wires into the V+ and V- contact on the terminal block connector. The device supports dual DC power input, the typical power source is DC 24V (range from 12~48VDC). Insert the SIM Unlock the front plate of Dual SIM Socket. Insert the SIM card into SIM

1 (Default startup SIM Socket is SIM 1) before power on system. The system may take around

1 minutes to startup, and then it will automatically connect to your ISP. If you want to use SIM

2 for carrier provider redundant, please insert the

2 SIM cards before power on the system. If you want to use SIM

2 as startup SIM socket, please go to Web GUI to modify the setting. If you insert the SIM after power on, the system may take around

30 second to re-read the SIM card info. If the Cellular connection is not connected, please go to Web GUI to check the Cellular Status, Settings or download the debug info for us. Mounting The Unit/Antenna and well Ground is MUST JetWave

2316 supports Din-Rail mounting, the mounting kit is pre-installed. You can mount the device to the DIN Rail directly. Connect the Ethernet cable, Antenna, extended antenna cable and Ground before power on the system. Grounding is important and MUST in field. The JetWave

2316 Series provides web management interface for basic and advanced settings. Before configuration, please make sure your system meets the following requirements: A computer coupled with 10/100/1000 Base-T(X) adapter. Configure the computer with a static IP address of 192.168.10.X/192.168.1.x (X cannot be 0, 1, nor 255). The product works as Router mode in default. The GT1 to GT4, GF1 and GF2 are LAN ports, the default IP address is 192.168.10.1 . The default IP Address of WAN port is 192.168.1.1 The WIFI default setting of JetWave

2316 is AP mode, SSID is JetWave2300_1 , operate in 2437MHz (channel 6). Open web browser (Ex: IE, Chrome, Firefox…) and enter the IP address of the product. You will see the System Login page. The default User Name is admin . The default Password is admin . Check User Manual for advanced settings. IF the web browser is not access, please check your firewall, JAVA version or contact your support window for further help. Note: If you forget the IP Address, you can use Korenix View Utility to search the device'

s IP address, it can be found at Download page of the Korenix web site: http://www.korenix.com Appearance Web GUI Installation The Korenix View Utility provides you convenient tool to scan the network and configure the connected Korenix device. Step 1: Open the Korenix View Utility. (Must later than JetView V1.6) Step 2: Select the correct NIC (Network Interface Card) from the NIC list. Step 3: Click Discovery , and then the Nodes and its IP address can be found and listed in Node list. Step 4: After you scan the network, select the device and click Open Web GUI to access the web management interface. You can also modify the IP address/Netmask directly on the selected entry and then click Change IP to change IP settings. Note: Please check the User Manual to configure the other software settings.