PDF《Murata Bluetooth mesh Node》

5 Subject to change without notice. Copyright ? Murata Manufacturing Co., Ltd. All rights reserved. 4. Tools Required ? Bluetooth mesh Node / Locknut ? Compatible LED driver ? Luminaire with LED modules ?

24 to

18 AWG (0.2-0.75mm2 ) solid or stranded wires ? Hole saw ? Neodymium magnet for factory reset (See Section 14) ? Provisioning mobile app (See Section 15) 5. Compatible LED Drivers The Bluetooth mesh Node works best with LED drivers that have 0-10V dimming, dim-to-off and 12VDC auxiliary power features. Please contact your Murata sales representative to check the compatibility. 6. Wire Specifications Wire Type Wire Gauge Inserting Wire Removing Wire Solid

24 to

18 AWG (0.2-0.75 mm2 ) Direct push-in Press the push-button to remove wire Stranded

24 to

18 AWG (0.2-0.75 mm2 ) Press the push-button while inserting wire Press the push-button to remove wire Strip Length 0.28-0.35 in. (7-9 mm) Conductor Insulation 1. Press the push-button 2. Pull the wire out 1PR-DG Rev. 1.2 Page

6 Subject to change without notice. Copyright ? Murata Manufacturing Co., Ltd. All rights reserved. 7. Not Recommended Practice Sensor Controller Node ? DO NOT install the Sensor Controller Node where the direct light can be detected. ? Install in a location that the sensor can be exposed outside and be faced directly below to the floor. ? Install away from the light source and LED driver to avoid radiated heat. Sensor-less Controller Node ? DO NOT embed the bezel of the Sensor-less Node in a location surrounded by metallic boards. 8. Terminal Assignment and Temperature Measurement Point Tc 1PR-DG Rev. 1.2 Page

7 Subject to change without notice. Copyright ? Murata Manufacturing Co., Ltd. All rights reserved. 9. Wiring Diagram Auxiliary

12 VDC supply from LED Driver External Power Supply 1PR-DG Rev. 1.2 Page

8 Subject to change without notice. Copyright ? Murata Manufacturing Co., Ltd. All rights reserved. 10. Dimensions Sensor Controller Node Sensor-less Controller Node 1PR-DG Rev. 1.2 Page

9 Subject to change without notice. Copyright ? Murata Manufacturing Co., Ltd. All rights reserved. 11. Installation Step Description Figure

1 Make sure the luminaire is de-energized.

2 Determine the location for the Bluetooth mesh Node in the luminaire and make a 7/8 inch (22.2-23.2 mm or 1/2 trade size) diameter hole.

3 Insert the Bluetooth mesh Node through the hole.

4 Use the locknut from the rear of the Bluetooth mesh Node to fix it.

5 Connect the Bluetooth mesh Node with a compatible LED driver in accordance with Wiring Diagram and Terminal Assignment.

6 Install the luminaire in the ceiling and energize it. 12. Recommended End-of-Line Test When the luminaire is powered on before provisioning, it starts dimming up and down in the following sequence automatically. Make sure the wiring and LED driver settings (if programmable) in case that the luminaire behaves differently or it is not turned on. 1PR-DG Rev. 1.2 Page

10 Subject to change without notice. Copyright ? Murata Manufacturing Co., Ltd. All rights reserved. 13. LED Indicators Green LED (Network Status) Fast blink (300 ms cycle) Unprovisioned Slow blink (2000 ms cycle) Provisioned Blink twice Mesh packet received Long blink Factory reset Red LED (Motion Sensor Status) Blink once Motion detected Note: LED indicators are not available in the Sensor-less Controller Node. 14. Factory Reset The Bluetooth mesh Node can be reset to the Unprovisioned Mode by placing a strong magnet (e.g. neodymium magnet) near the center of the bezel for

5 seconds. See below for the magnet-sensitive areas. Once the factory reset is done successfully, the luminaire behaves as described in Section 12. Sensor Controller Node Sensor-less Controller Node 1PR-DG Rev. 1.2 Page