PDF《产品规格书PRODUCT SPECIFICATION》

REV.

A 第1页共7页产品规格书PRODUCT SPECIFICATION 【1】适用范围 SCOPE 本规格书适用于 0.5mm Pitch H=2.0 FPC 掀盖卧式 SMT 型连结器系列. This specification covers the 0.5mm Pitch H=2.0 FPC Easy-on R/A SMT type connectors series. 【2】外观尺寸 CONNECTOR DIMENSIONS 请参照图面 See attached drawings. 【3】材质 MATERIAL 绝缘胶体 Housing: LCP 颜色 Color:白色 White 耐燃等级(UL94V-0)Flammability Rating(UL94V-0). 后盖 Actuator: LCP 颜色 Color:黑色 Black 耐燃等级(UL94V-0)Flammability Rating(UL94V-0). 端子 Terminal: 磷青铜 Phosphor Bronze. 焊片 Fitting Nail:磷青铜 Phosphor Bronze. 【4】建议 P.C.B LAYOUT 图ACCOMMODATED P.C.B LAYOUT 请参照图面 See attached drawings. 【5】等级 RATING 项目ITEM 规格SPECIFICATIONS 最大容许电压 Operating Voltage(Max.) 50V AC 最大容许电流 Current Rating(Max.) 0.5A DC 使用温度范围 Operating Temperature range -55°C?+85°C 使用湿度范围 Operating humidity range 相对湿度90%以下 Relative humidity 90% max. 保存温度范围 Storage temperature range -10°C ? +50°C 保存湿度范围 Storage humidity range 相对湿度90%以下 Relative humidity 90% max. *:包含电流通过所产生的上升温度 Including terminal temperature rise. REV. A 第2页共7页【6】性能 PERFORMANCE 6.1 电气特性 ELECTRICAL PERFORMANCE 项目 ITEM 测试条件 TEST CONDITION 规格 REQUIRMENT 接触阻抗 Contact Resistance 将样品与适合之FPC连接, 测试电 压20mV, 限电流10mA下进行阻抗 测试.(EIA-364-23) Mate applicable FPC and measure by dry circuit, 20mV Max, 10mA. (EIA-364-23)

30 m?最大.

30 m? Max. 绝缘阻抗 Insulation Resistance 将样品与适合之FPC连接, 提供相 邻端子间测试电压500V DC进行 绝缘阻抗测试(EIA-364-21) Mate applicable FPC and apply 500V DC between adjacent terminal or ground. (EIA-364-21)

500 M?最小.

500 M? Min. 耐电压 Dielectric Strength 将样品与适合之FPC连接, 相邻端 子间需可承受250V AC(rms) 1分钟.(EIA-364-20) Mate applicable FPC, apply 250V AC(rms) for1 minute between adjacent terminal or ground.(EIA-364-20) 目视外观无任何损坏异状 No Breakdown 6.2 机械特性 MECHANICAL PERFORMANCE 项目 ITEM 测试条件 TEST CONDITION 规格 REQUIRMENT FPC保持力 FPC Retention Force 将盖子盖上,与FPC连接,以操作 速度每分钟位移25±3mm进行FPC 保持力测试. Insert the actuator, pull the FPC at a rate of 25±3mm per minute. Pos.x 0.30N最小 Pos.x 0.30N Min. 端子保持力 Terminal Retention Force 端子与Housing组装后,以操作速 度每分钟位移25±3mm将端子拔出 Housing,进行端子保持力测试. Apply axial pull out force at the rate of 25±3 mm/minute on the terminal assembled in the housing. 3N最小. 3N Min. REV. A 第3页共7页项目 ITEM 测试条件 TEST CONDITION 规格 REQUIRMENT 焊片保持力 Fitting Nail Retention Force 焊片与Housing组装后,以操作速 度每分钟位移25±3mm将焊片拔出 Housing,进行焊片保持力测试. Apply axial pull out force at the rate of 25±3 mm/minute on the Fitting Nail assembled in the housing. 1.0N最小. 1.0N Min 6.3 环境特性及其它性能 ENVIRONMENTAL PERFORMANCE AND OTHERS 项目 ITEM 测试条件 TEST CONDITION 规格 REQUIRMENT 耐久性 Durability 将盖子与FPC反复连接,以每分钟 小于10 cycles连续操作20次. Insert and withdraw actuator up to

20 cycles at the speed rate of less than

10 cycles/minute. 接触阻抗 Contact Resistance 60m?最大. 60m? Max. 温度上升 Temperature Rise 量测通过FPC最大容许电流时,样品接触点之温升(EIA-364-70 METHOD 2) Mate applicable FPC and measure the temperature rise of contact when the maximum AC rated current is passed. 温升 Temperature rise 30°C最大. 30°C Max. 耐振性 Vibration 通过DC电流1mA,位移相对距离 1.5mm,振动周期10?55?10 Hz在 1分钟内, 持续2小时, 方向在X,Y,Z 轴做测试. (EIA-364-28 Condition I) Mate connectors and subject to the following vibration conditions, for period of