PDF《产品规格书PRODUCT SPECIFICATION》

2 hours in each of

3 mutually perpendicular axes, passing DC 1mA during the test. Amplitude : 1.5mm P-P Frequency : 10?55?10 Hz in

1 minute. Duration :

2 hours in each of X,Y,Z axes. (EIA-364-28 Condition I) 外观 Appearance 目视外观无任 何损坏异状 NoDamage 接触阻抗 Contact Resistance 60m?最大. 60m? Max. 瞬间断电 Discontinuity 1μsec最大 1μsec Max. REV. A 第4页共7页项目 ITEM 测试条件 TEST CONDITION 规格 REQUIRMENT 耐冲击性 Shock 将样品与适合之FPC连接,通过DC

1 mA测试条件, 连续测试3次. 在X、 Y、 Z 3轴6个垂直方向施予重力加 速度490m/s2 {50G} 冲击. (EIA-364-27, test condition A) Mate applicable FPC and subject to the following shock conditions.

3 times of shocks shall be applied for each

6 directions along

3 mutually perpendicular axes, passing DC

1 mA current during the test. (Total of

18 shocks) Peak value : 490m/s2 {50G}(EIA-364-27, test condition A) 外观 Appearance 目视外观无任 何损坏异状 NoDamage 接触阻抗 Contact Resistance 60m? 最大. 60m? Max. 瞬间断电 Discontinuity 1μsec 最大 1μsec Max. 耐热性 Heat Resistance 将样品与适合之FPC连接,置于环 境温度85±2°C测试时间96小时,再 置放于室温下1?2小时. Mate applicable FPC and expose to 85±2°C for

96 hours. Upon completion of the exposure period, the test specimens shall be conditioned at ambient room conditions for

1 to

2 hours, after which the specified measurements shall be performed. 外观 Appearance 目视外观无任 何损坏异状 NoDamage 接触阻抗 Contact Resistance 60m? 最大. 60m? Max. 耐寒性 Cold Resistance 将样品与适合之FPC连接,置于环 境温度-40±2°C,测试时间96小时, 再置放于室温下1?2小时. Mate applicable FPC and expose to -40±2°C for

96 hours. Upon completion of the exposure period, the test specimens shall be conditioned at ambient room conditions for

1 to

2 hours, after which the specified measurements shall be performed. 外观 Appearance 目视外观无任 何损坏异状 NoDamage 接触阻抗 Contact Resistance 60m? 最大. 60m? Max. REV. A 第5页共7页项目 ITEM 测试条件 TEST CONDITION 规格 REQUIRMENT 耐湿性 Humidity 将样品与适合之FPC连接,置于环 境温度60±2°C, 相对湿度90?95%, 测试时间96小时,再置放于室温 下1?2小时. Mate applicable FPC and expose to

60 ± 2°C, relative humidity

90 to 95% for

96 hours. Upon completion of the exposure period, the test specimens shall be conditioned at ambient room conditions for

1 to

2 hours, after which the specified measurements shall be performed. 外观 Appearance 目视外观无任 何损坏异状 NoDamage 接触阻抗 Contact Resistance 60m?最大. 60m?Max. 耐电压 Dielectric Strength 需能符合耐电 压测试 No Breakdown 绝缘阻抗 Insulation t Resistance

30 M? 最小.

30 M? Min 冷热冲击 Temperature Cycling 将样品与适合之FPC连接,承受5 cycles冷热冲击后置放于室温下1? 2小时.1 cycle time如下 a) -55±3°C 30分钟 b) +85±3°C 30分钟 Mate applicable FPC and subject to the following conditions for

5 cycles. Upon completion of the exposure period, the test specimens shall be conditioned at ambient room conditions for

1 to

2 hours, after which the specified measurements shall be performed.

1 cycle a) -55±3°C 30minutes b) +85±3°C 30minutes 外观 Appearance 目视外观无任 何损坏异状 NoDamage 接触阻抗 Contact Resistance 60m? 最大. 60m? Max. 盐水喷雾 Salt Spray 将样品与适合之FPC连接,使用 5±1%浓度盐水,测试温度35±2°C, 测试时间48±4小时,后于室温下使 用清水冲洗后再干燥. Mate applicable FPC and expose to the following salt mist conditions. Upon completion of the exposure period, salt deposits shall be removed by a gentle wash or dip in running water, after which the specified measurements shall be performed. NaCl solution Concentration :