编辑: 阿拉蕾 2019-07-17
OM-CP-WIND101A-KIT Wind Speed Data Logging System MQS5792/1216 Xxxxx Xxxxxx Xxxxx Xxxxxx Xxxxxxxx M0000/0016 INSTRUCTION SHEET Shop online at omega.

comSM e-mail: [email protected] For latest product manuals: www.omegamanual.info Xxxxx Xxxxxx Xxxxx Xxxxxx Xxxxxxxx M0000/0016 INSTRUCTION SHEET Shop online at omega.comSM e-mail: [email protected] For latest product manuals: www.omegamanual.info

2 Product Overview The OM-CP-WIND101A-KIT is a complete system to accurately measure and record wind speed. This low cost wind speed recording system comes complete with the OM-CP-PULSE101A data logger, weatherproof enclosure, a three-cup anemometer and all the necessary cabling to quickly get up-and-running. Changing the Reading Rate The OM-CP-WIND101A-KIT comes programmed to provide the average wind speed using a

10 second reading rate. If a different reading rate is desired the engineering units gain will have to be reprogrammed on the device. To do this, click the Engineering Units button from the Start Device dialog box, and use the Device Units Wizard. Follow the wizard'

s prompts to: - Enable use of portable engineering units. - Enter an appropriate description and label (MPH or KPH). - Enter the Offset and Gain values (offset=0 / gain=see below). - Enable Engineering Units. - Click the Finish button to save the units to the device. Engineering Units Gain Quick Reference Reading Rate MPH KPH M/S KNOTS

2 sec 0.425 0.68397 0.18999 0.36931

5 sec 0.17 0.27359 0.075997 0.14773

10 sec 0.085 0.13679 0.037998 0.073863

30 sec 0.028333 0.045598 0.012666 0.024621

1 min 0.014167 0.022799 0.006331 0.0123100

5 min 0.0028333 0.0045598 0.0012666 0.0024621

10 min 0.0014167 0.0022799 0.00063331 0.0012310 LEDs - Green LED blinks:

10 seconds to indicate logging,

15 seconds to indicate delay start mode - Red LED blinks:

10 seconds to indicate low battery and/or memory Password Protection An optional password may be programmed into the device to restrict access to configuration options. Data may be read out without the password. Multiple Start/Stop Mode Activation - To start device: Press and hold the pushbutton for

5 seconds, the green LED will flash during this time. The device has started logging. - To stop the device: Press and hold the pushbutton for

5 seconds, the red LED will flash during this time. The device has stopped logging. OM-CP-WIND101A-KIT

3 Troubleshooting Tips Why is the wireless data logger not appearing in the software? If the OM-CP-WIND101A-KIT doesn'

t appear in the Connected Devices panel, or an error message is received while using the OM-CP-WIND101A-KIT, try the following: ? Check that the OM-CP-IFC200 is properly connected. For more information, see Troubleshooting Interface Cable problems (below). ? Ensure that the battery is not discharged. For best voltage accuracy, use a voltage meter connected to the battery of the device. If possible, try switching the battery with a new OM-CP-BAT105. ? Ensure that no other Omega software is running in the background. ? Ensure that Omega Software is being used. ? Ensure that the Connected Devices panel is large enough to display devices. This can be verified by positioning the cursor on the edge of the Connected Devices panel until the resize cursor appears, then dragging the edge of the panel to resize it. The screen layout may also be reset in the options menu by selecting File, Options, and scrolling to the bottom. Troubleshooting Interface Cable problems Check that the software properly recognizes the connected OM-CP-IFC200. If the data logger is not appearing in the Connected Devices list, it may be that the OM-CP-IFC200 is not properly connected. 1. In the software, click the File button, then click Options. 2. In the Options window, click Communications. 3. The Detected Interfaces box will list all of the available communication interfaces. If the OM-CP-IFC200 is listed here, then the software has correctly recognized and is ready to use it. Check that Windows recognizes the connected OM-CP-IFC200. If the software does not recognize the OM-CP-IFC200, there may be a problem with Windows or the USB drivers. 1. In Windows, click Start, right-click Computer and choose Properties or press Windows+Break as a key- board shortcut. 2. Click Device Manager in the left hand column. 3. Double click Universal Serial Bus Controllers. 4. Look for an entry for Data logger Interface. 5. If the entry is present, and there are no warning messages or icons, then windows has correctly recognized the connected OM-CP-IFC200. 6. If the entry is not present, or has an exclamation point icon next to it, the USB drivers may need to be installed. These are available on the software flash drive included with the OM-CP-IFC200. Ensure that the USB end of the OM-CP-IFC200 is securely connected to the computer. 1. Locate the USB-A plug of the OM-CP-IFC200. 2. If the interface cable is connected to the PC, unplug it. Wait ten seconds. 3. Reconnect the cable to the PC. 4. Check to make sure that the red LED is lit, indicating a successful connection. OM-CP-WIND101A-KIT

下载(注:源文件不在本站服务器,都将跳转到源网站下载)
备用下载
发帖评论
相关话题
发布一个新话题